SlideShare ist ein Scribd-Unternehmen logo
1 von 10
Downloaden Sie, um offline zu lesen
International Journal of Engineering Research and Development
e-ISSN : 2278-067X, p-ISSN : 2278-800X, www.ijerd.com
Volume 2, Issue 7 (August 2012), PP. 26-35


       Modeling and Analysis of Self Excited Slip Ring Induction
              Generator Using Newton Raphson Method
                                        S.Mathankumar1, P.Loganathan2
         1, 2
                Assistant Professor, Department of Electrical & Electronics Engineering, V.M.K.V.Engineering College,
                                 Vinayaka Missions University, Salem, Tamil Nadu, India -636 308.



Abstract––In this paper deals with steady state analysis of self-excited slip ring induction generator (SESRIG) is
performed using Newton- Raphson method. By varying effective rotor resistance of a self excited slip ring induction
generator, the magnitude and frequency of the output voltage can be controlled over a wide speed range. A steady state
analysis based on normalized equivalent circuit enables the control characteristics to be deduced. In the wind driven
SESRIG system the rotor speed is varied along with wind speed. For a given stator load, both frequency and voltage can
be maintained constant as speed is varied by changing rotor resistance, with constant excitation capacitance. The
proposed scheme may be used in low cost variable speed wind energy system for providing good quality electric power to
remote regions.

Keywords––SESRIG, Newton- Raphson Method, Rotor Resistance

                                                 I.       INTRODUCTION
Self-excitation in an induction generator occurs when the rotor is driven by a Prime mover and a suitable capacitance is
connected across the stator terminals. Under such conditions, the terminal capacitance furnishes the lagging reactive power
necessary for establishing the air gap flux and the machine is often referred to as a self-excited induction generator (SEIG).
SEIGs increasingly utilized in stand-alone generation systems that employ wind or hydro power. Unlike introduction
generators connected to the power utility grid, both the frequency and the terminal voltage of the SEIG vary with load even
when the rotor speed is maintained constant. An increase in the rotor speed will result in a proportionate increase in
frequency, often accompanied by severe over voltage and excessive current. Recently, there has been rigorous research on
the voltage and frequency control of squirrel – cage type SEIGs, but relatively little research efforts have been devoted to the
use of the slip ring induction machine for generator applications.

a. Advantages
      When a grid connection is permissible, the slip-ring machine may be operated as a double-output induction
         generator (DOIG) using the slip-energy recovery technique.
      In the case of a self-excited slip-ring induction generator (SESRIG), the system cost can be further reduced by the
         use of a simple rotor resistance controller.
      Only a capacitor bank needs to be connected to the stator terminals, the SESRIG provides a good quality ac source
         with little harmonic distortion to the stator load.
      Advantageous feature of the SESRIG is that independent control of the voltage and frequency can be achieved
         easily. Even with a wide variation in speed, the generator frequency can be maintained reasonably constant by
         rotor resistance control, while the voltage can be controlled by varying the excitation capacitance.
      Although the slip-ring machine is more expensive and requires more maintenance, it permits rotor slip-power
         control when driven by a variable-speed turbine.

                                      II.             CIRCUIT ARRANGEMENT
                        .                                       Slip-ring        RX2
                                                                induction
                                            ZL
                                                               machine
                                            ZL
                                                                                       RX2

                                            ZL
                                                 c       c                             RX2
                                                                Turbine

                                   Fig. 2.1. The circuit arrangement of a three phase SESRIG

                                                               26
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

   In this paper, the voltage and frequency control of a three phase SESRIG by variation of external rotor resistance will be
   investigated. Based on a normalized equivalent circuit model, the frequency and voltage characteristics are deduced and
 experimental results are presented to verify the feasibility of the control method. Practical implementation of a closed loop
                           scheme that uses chopper-controlled rotor resistance will also be described.
           Fig. 2.1 shows the circuit arrangement of a three phase SESRIG. The excitation capacitance „C‟ is required for
initiating voltage buildup and maintaining the output voltage. It is noticed that the electrical output power is dissipated in
both the stator impedance ZL as well as the external rotor resistance RX2. Hence, the machine may also be regarded as a
DOIG if the power is Rx2 is effectively utilized.

                                         III.            MATHEMATICAL MODELING
3.1. Equivalent circuit analysis of SESRIG
          The SESRIG is actually an induction motor that driven by a prime mover while its stator excitation provided by an
external capacitor connected to the stator. The excitation capacitance is required for initiating voltage buildup and
maintaining the output voltage.




                                              Figure.3.1 Per-phase Equivalent circuit of SESRIG

          Fig 3.1 Shows the per phase equivalent circuit of SESRIG where the rotor resistance R2 is the sum of the rotor
winding resistance and external rotor resistance. The circuit has been normalized to the base (rated) frequency through the
introduction of the per- unit frequency „a‟ and the per-unit speed „b‟. Various methods have been developed for solution of
the SESRIG equivalent circuit. Adopting the nodal admittance, the following relation ship may be established for successful
voltage build-up.

3.2. Nodal admittance method
          This method considers the admittances connected across the nodes which define the air gap. By equating the sum
of real parts to zero (which is equivalent to active power balance), a polynomial in “a” is obtained. Xm can be determined
upon equating the sum of imaginary parts to zero, using the value of “a” obtained after solving the polynomial.

          Yt+Ym+Y2=0                                                                                                     (1)

Where,
                 1                  1
          Yt                              G t  jBt                                                                    (2)
                 zt            Zac  Zab

                           1
          Ym   j                  G m  jBt                                                                            (3)
                       Xm
                               1
          Y2                            G m  jBt                                                                       (4)
                      R2
                                jX 2
                  ab

Equating the real and imaginary parts in 1 to zero respectively, the following equations in real number are obtained.

                       Gt+Gm+G2 = 0                                                                                       (5)

                           Bt+Bm+B2 = 0                                                                                   (6)

REAL PARTS(Gt+Gm+G2 )=
                        -aXmbXCX2+ aXmXLXC- aXmbXLXC- aXmbR1RL- aXmbX1XC- abX2XLXC- abX2R1RL-
abX2X1*XC +a2XmRLR2+ a2XmXCX2+ a2XmR1RL+ a2XmX1XC+ a2X2XLXC+ a2X2R1RL+ a2X2X1XC+ a2X1RLR2+ a2XLR1R2
+a3XmbXLX2+ a3XmbX1XL+a2bX1XLX2- a4XmXLX2-a4XmX1XL+a4X1XLX2-RLR2XC
                                                                                                (7)


                                                                     27
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

IMAGINARY PARTS(Bt+Bm+B2 )=
                              aXmXCR2- aXmRLXC- aXmR1XC - aR2XLXC- aR1RLR2- aR2X1XC- aX2RLXC- aX2R1XC-
a2XmbX2RL-a2XmbX1RL-a2XmbXLR1-a2bX2X1RL- a2bX2XLR1+ a3XmXLR2+ a3XmX2RL+ a3XmX1RL+ a3XmXLR1 +a3XLX1R2+
a3X2X1RL+ a3X2XLR1+ XmbRLXC+ XmbR1XC+ bX2RLXC +bX2R1XC
                                                                                                   (8)

3.3. Newton-Raphson method
By taking the Coefficients a and Xm in the equations(7), (8) the real and imaginary parts can be given by

                                             2
h1  ( f 0 X m  f1 ) a  ( f 2 X m  f 3 ) a 
                                                                                                               (9)
                  3                      4
( f 4 X m  f 5) a  ( f 6 X m  f 7 ) a  f 8
                                                                    2
h 2  ( g 0 X m  g1 ) a  ( g 2 X m  g 3 ) a
                                                                                                             (10)
                          3                                     4
 ( g 4 X m  g 5) a               ( g 6 X m  g 7 )a               g8

The constants are given in appendix A-1.

h1
         ( f 0 X m  f1 )  2( f 2 X m  f 3 ) a 
 a                                                                                                           (11)
                         2
3( f 4 X m  f 5 ) a           4( f 6 X m  f 7 ) a 3

  h 2
            ( g 0 X m  g1 )  2( g 2 X m  g 3 ) a 
  a                                                                                                          (12)
                              2
 3( g 4 X m  g 5 ) a               4( g 6 X m  g 7 ) a 3

 h1                          2                3            4
            f0 a  f2 a               f4 a        f6 a                                                     (13)
X m


 h 2                             2            3                4
            g0a  g2a                 g4a          g6a                                                     (14)
X m
The „J‟ matrix is given by

    h1                        
                              h1
    a                   X m
                                
                               
J                                                                                                          (15)
                               
    h 2                  h 2
                                
    a
                         X m 
From the equations (7) & (8), the matrix „K‟ is given by

            h1 
K                                                                                                       (16)
            h 2 
The inverse of „j‟ matrix is given by

      1       1
 J                adj[ J ]                                                                                  (17)
               J




                                                                           28
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

The value of   a    and    X m   is calculated by

a         1
Xm  [ J ] [ K ]                                                                                                    (18)
 
The value of „a‟ and „Xm‟ is calculated using -R method from equations (19) and (20).

a new = a old + a                                                                                                     (19)

Xm new= Xm old + X m                                                                                                  (20)

          The induction machine used here is given in appendix A-2 The air gap voltage E1 is expressed in terms of Xm by a
piece wise linerized equation of the form.
          A stable operating point exists, provided that X m is less than the actuated value having determined all constants
including Xm and El. The equivalent circuit of fig is complexly solved for the steady state performance of the induction
generator.

       The stator phase current is given by
                  E1
       I1                                                                                                             (22)
               Z LC  Z 1


                       where,
                                            R1
                                     Z1           jX 1
                                            a
                                             R2
                                     Z2                jX 2
                                            ab
                                            RL
                                     ZL           jX L                                                               (23)
                                             a
                                                  Xc
                                     Zc   j
                                                   Z
                                                 a
                                     Z LC  Z L // Z C



     The stator phase voltage is given by ,
     V1= (IL*ZL*a)                                                                                                     (24)

      Pout =3*IL2*RL                                                                                                   (25)

       Where,
                 IL= (I1*ZC)/ (ZL+ZC)                                                                                  (26)

3.4. Computational Algorithm
     1. Read all the machine required parameters.
     2. Determine the value of the constants given in appendix A-1.
     3. Assume the initial value of a and Xm (a= b in p.u and Xm= saturated value in p.u).
     4. Determine the value of real and imaginary terms given in equations (7) and (8).
     5. If the value of h1 and h2 are greater than tolerance (0.0001)go to next Step otherwise go to step 11.
     6. From the „K‟ matrix given in equation (16).
     7. Determine the partial derivatives of h1 and h2 with respect to a and Xm given in equation (11), (12), (13) and (14).
     8. Form „J‟ matrix and inverse of „J‟ matrix given in equ (15),(17)steps.
     9. Determine the value of a and Xm given in equation (18).
     10. Update the value of a and Xm given in the equation (19) and (20) and go to step 4.
     11. Obtain the air gap voltage E1 expressed in terms of
           Xm given in equation (21).
     12. Determine the stator phase current I1 given in equation (22).
     13. Determine the stator phase voltage V1 and output power Pout given in equation (24) & (25).
     14. Stop.
                                                                29
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

IV. PERFORMANCE CHARACTERISTICS OF SESRIG
4.1. Results and discussion
           The variation of per unit frequency, magnetizing reactance, air gap voltage, stator phase voltage, stator phase
current and output power with respect to change in per unit speed at different rotor resistance are given in tables 4.1,4.2, and
4.3. The stator voltage, stator current, frequency and output power characteristics of the SESRIG for different values of
external rotor resistance RX2 shown in figures 4.1, 4.2 and 4.3 respectively. These figures show that, increase in speed has
proportionate increase in output voltage, current, frequency and power. It is observed that increasing Rx2 has the effect of
shifting the performance characteristics to the right-hand side of the speed axis. At a rotor speed of 1.05 p.u or above, the
generator voltage or frequency can be maintained at rated value by varying RX2. This feature will be employed for voltage
and frequency control of the SESRIG. It is observed that increasing Rx2 has the effect of shifting the performance
characteristics to the right-hand side of the speed axis. At a rotor speed of 1.05 p.u or above, the generator voltage or
frequency can be maintained at rated value by varying RX2. This feature will be employed for voltage and frequency control
of the SESRIG. The operating speed range of the SESRIG depends upon the maximum value of R X2 available, the rated
voltage of the rotor winding, as well as the mechanical constraints of the turbine The result shows that by varying rotor
resistance values, the magnitude and frequency of voltage can be controlled over a wide speed range. The variation of per
unit frequency, magnetizing reactance, air gap, stator phase voltage, and stator phase current, with respect to change in per
unit speed at different stator resistance are given in tables 4.4, 4.5 and 4.6. The stator voltage, stator current, frequency
characteristics of the SESRIG for different values of external stator resistance RX1 shown in figures 4.4, 4.5 and 4.6.
respectively. The results from the figures show that, by varying stator resistance values, the magnitude of stator phase
voltage and current can be controlled. But the frequency is remaining unchanged with respect to various stator resistances.
The stator resistance has considerable influence over the stator voltage and current. So the characteristics are useful to design
the machine for specified system.

4.2. Tabulation of Results
4.2.1 Effects of rotor resistance variations
For, Rx2=0.00 p.u ; C=47μF ; RL=3 p.u

                            b           a         Xm           E1          V1          I1              Pout
                         0.9000      0.8663      1.8645     0.8375      0.7567      0.5348        0.5726
                         0.9500      0.9137      1.6671     0.9067      0.8702      0.6414        0.7572
                         1.0000      0.9610      1.4988     0.9627      0.9791      0.7515        0.9586
                         1.0500      1.0080      1.3542     1.0108      1.0870      0.8676        1.1816
                         1.1000      1.0550      1.2290     1.0524      1.1945      0.9901        1.4268
                         1.1500      1.1017      1.1200     1.0887      1.3018      1.1193        1.6946
                         1.2000      1.1482      1.0246     1.1204      1.4093      1.2553        1.9860
                         1.2500      1.1945      0.9406     1.1484      1.5172      1.3985        2.3019
                         1.3000      1.2406      0.8663     1.1731      1.6259      1.5491        2.6436
                         1.3500      1.2864      0.8004     1.1950      1.7356      1.7073        3.0122
                         1.4000      1.3320      0.7417     1.2145      1.8464      1.8734        3.4092

                    Table. 4.1. Results for various speed values at RX2=0.00 (all the values are in p.u)




                                                                                            Rx2=0.00 p.u
                                                                                            Rx2=0.18 p.u
                                                                                            Rx2=0.36 p.u
                                                                                            Rx2=0.54 p.u
                                                                                            RL=3 p.u
                                                                                            C=47μF




           Graph.4.1.Stator phase voltage with respect to per unit speed for various Rotor resistance values.

                                                              30
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

For, Rx2=0.18p.u ; C=47μF ; RL=3 p.u
                     B          a          Xm         E1           V1            I1          Pout
                    0.90      0.8125     2.1321     0.6736       0.5664       0.3812       0.3208
                    0.95      0.8561     1.9113     0.8201       0.7312       0.5120       0.5346
                    1.00      0.8994     1.7229     0.8881       0.8372       0.6093       0.7008
                    1.05      0.9424     1.5610     0.9420       0.9367       0.7077       0.8774
                    1.10      0.9851     1.4208     0.9886       1.0349       0.8105       1.0710
                    1.15      1.0274     1.2986     1.0292       1.1321       0.9180       1.2816
                    1.20      1.0695     1.1916     1.0649       1.2285       1.0301       1.5093
                    1.25      1.1111     1.0973     1.0962       1.3244       1.1471       1.7542
                    1.30      1.1524     1.0139     1.1240       1.4201       1.2689       2.0166
                    1.35      1.1932     0.9397     1.1487       1.5155       1.3956       2.2968
                    1.40      1.2336     0.8735     1.1707       1.6110       1.5273       2.5953
                  Table 4.2. Results for various speed values at RX2=0.18 (all the values are in p.u)




                                                                                       Rx2=0.00 p.u
                                                                                       Rx2=0.18 p.u
                                                                                       Rx2=0.36 p.u
                                                                                       Rx2=0.54 p.u
                                                                                       RL=3 p.u
                                                                                       C=47μF




         Graph.4.2.Stator phase current with respect to per unit speed for various Rotor resistance values.

For , Rx2=0.36 p.u ; C=47μF ; RL=3p.u
                        b        a          Xm         E1          V1           I1         Pout
                      0.90     0.7666     2.4069     0.0000      0.0000      0.0000      0.0000
                      0.95     0.8072     2.1616     0.6407      0.5349      0.3582      0.2861
                      1.00     0.8475     1.9523     0.8049      0.7095      0.4931      0.5035
                      1.05     0.8874     1.7723     0.8717      0.8092      0.5828      0.6549
                      1.10     0.9270     1.6165     0.9235      0.9011      0.6718      0.8119
                      1.15     0.9661     1.4807     0.9687      0.9914      0.7642      0.9828
                      1.20     1.0049     1.3617     1.0083      1.0804      0.8601      1.1673
                      1.25     1.0433     1.2568     1.0431      1.1684      0.9596      1.3652
                      1.30     1.0812     1.1640     1.0740      1.2555      1.0625      1.5763
                      1.35     1.1187     1.0815     1.1015      1.3419      1.1690      1.8008
                     1.40      1.1558      1.0078    1.1260      1.4278      1.2791      2.0386
                  Table 4.3. Results for various speed values at RX2=0.36 (all the values are in p.u)




                                                           31
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method




                                                                                      Rx2=0.00 p.u
                                                                                      Rx2=0.18 p.u
                                                                                      Rx2=0.36 p.u
                                                                                      Rx2=0.54 p.u
                                                                                      RL=3 p.u
                                                                                      C=47μF




          Graph. 4.3. Per unit frequency with respect to per unit speed for various Rotor resistance values.


For, Rx2=0.54p.u ; C=47μF ; RL=3 p.u
                     B         a            Xm           E1        V1           I1               Pout
                   1.00       0.8049      2.1743     0.6266      0.5215      0.3484          0.2720
                   1.05       0.8425      1.9763     0.7960      0.6971      0.4822          0.4859
                   1.10       0.8798      1.8048     0.8596      0.7903      0.5653          0.6246
                   1.15       0.9166      1.6554     0.9105      0.8771      0.6480          0.7692
                   1.20       0.9530      1.5245     0.9541      0.9611      0.7327          0.9237
                   1.25       0.9890      1.4090     0.9925      1.0438      0.8201          1.0895
                   1.30       1.0245      1.3068     1.0265      1.1253      0.9103          1.2662
                   1.35       1.0596      1.2159     1.0568      1.2057      1.0032          1.4538
                   1.40       1.0942      1.1348     1.0838      1.2853      1.0988         1.6520
                  Table 4.4. Results for various speed values at RX2=0.54 (all the values are in p.u)


                                          Rx2=0.00 p.u
                                          Rx2=0.18 p.u
                                          Rx2=0.36 p.u
                                          Rx2=0.54 p.u
                                          RL=3 p.u
                                          C=47μF




        Graph. 4.4. Per unit Output power with respect to per unit speed for various Rotor resistance values.




                                                          32
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

4.2.2. Effects of stator resistance variations
For , Rx1=0.00 p.u ; C=47μF ; RL=3 p.u
                           b              a          Xm            E1             V1              I1
                        0.9000         0.8663      1.8645        0.8375         0.7567         0.5348
                       0.9500         0.9137       1.6671        0.9067         0.8702         0.6414
                       1.0000         0.9610       1.4988        0.9627         0.9791         0.7515
                       1.0500         1.0080       1.3542        1.0108         1.0870         0.8676
                       1.1000         1.0550       1.2290        1.0524         1.1945         0.9901
                       1.1500         1.1017       1.1200        1.0887         1.3018         1.1193
                       1.2000         1.1482       1.0246        1.1204         1.4093         1.2553
                       1.2500         1.1945       0.9406        1.1484         1.5172         1.3985
                       1.3000         1.2406       0.8663        1.1731         1.6259         1.5491
                       1.3500         1.2864       0.8004        1.1950         1.7356         1.7073
                      1.4000        1.3320         0.7417        1.2145        1.8464         1.8734
                    Table 4.5. Results for various speed values at RX1=0.00 (all the values are in p.u)



                                                                                    Rx1=0.00 p.u
                                                                                    Rx1=0.18 p.u
                                                                                    Rx1=0.36 p.u
                                                                                    Rx1=0.54 p.u
                                                                                    RL=3 p.u
                                                                                    C=47μF




           Graph.4.5. Stator phase voltage with respect to per unit speed for various stator resistance values

For, Rx1=0.18 p.u ; C=47μF ; RL=3 p.u
                        b           a                Xm            E1             V1              I1
                     0.9000      0.8635            2.0729        0.7394         0.6182         0.4358
                     0.9500      0.9102            1.8658        0.8370         0.7413         0.5447
                       1.0000         0.9568       1.6897        0.8991         0.8414         0.6435
                       1.0500         1.0029       1.5370        0.9499         0.9368         0.7446
                       1.1000         1.0489       1.4060        0.9935         1.0306         0.8502
                       1.1500         1.0947       1.2921        1.0314         1.1231         0.9605
                       1.2000         1.1401       1.1926        1.0645         1.2147         1.0755
                       1.2500         1.1853       1.1053        1.0936         1.3055         1.1952
                       1.3000         1.2301       1.0283        1.1192         1.3956         1.3198
                       1.3500         1.2746       0.9603        1.1418         1.4853         1.4492
                      1.4000         1.3188         0.9000       1.1619        1.5745         1.5834
                    Table. 4.6. Results for various speed values at RX1=0.18 (all the values are in p.u)




                                                            33
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method


                                                                                             Rx1=0.00 p.u
                                                                                             Rx1=0.18 p.u
                                                                                             Rx1=0.36 p.u
                                                                                             Rx1=0.54 p.u
                                                                                             RL=3 p.u
                                                                                             C=47μF




          Graph. 4.6. Stator phase current with respect to per unit speed for various stator resistance values.

For, Rx1=0.36 p.u ; C=47μF ; RL=3 p.u
                          B           A                 Xm             E1             V1               I1
                       0.9000      0.8619             2.3320         0.0000         0.0000          0.0000
                       0.9500      0.9084             2.1153         0.6923         0.5646          0.4142
                       1.0000      0.9546             1.9316         0.8126         0.6979          0.5328
                       1.0500      1.0003             1.7736         0.8712         0.7860          0.6234
                       1.1000      1.0460             1.6379         0.9164         0.8665          0.7131
                        1.1500         1.0913         1.5204         0.9555         0.9449          0.8059
                        1.2000        1.1364        1.4183      0.9894       1.0214         0.9017
                        1.2500        1.1811        1.3292      1.0191       1.0961         1.0005
                        1.3000        1.2256        1.2512      1.0450       1.1692         1.1022
                        1.3500        1.2698        1.1829      1.0677       1.2408         1.2066
                    Table 4.7. Results for various speed values at RX1=0.36 (all the values are in p.u)

                                                                                         Rx1=0.00 p.u
                                                                                         Rx1=0.18 p.u
                                                                                         Rx1=0.36 p.u
                                                                                         Rx1=0.54 p.u
                                                                                         RL=3 p.u
                                                                                         C=47μF




           Graph.4.7. Per unit frequency with respect to per unit speed for various stator resistance values.

                                              V.            CONCLUSION
          In this paper of work the voltage and frequency control of a self excited slip ring induction generator by varying
the external rotor resistance have been presented. Steady state modeling, performance and the control characteristic of the
SESRIG have been developed from an equivalent circuit analysis. It is shown that with constant load and excitation
capacitance, both frequency and the output voltage of the SESRIG can be maintained constant by varying rotor resistance
over wide range of speeds without exceeding the specified stator current limit. In future it is planned to develop a suitable
technique to vary the external rotor resistance automatically to achieve voltage and frequency control.

                                                     BIBLIOGRAPHY
  [1].   Swati Devabhaktuni and S.V.Jayaram Kumar, “Selection of Capacitors for the Self Excited Slip ring Induction Generator with
         External Rotor Capacitance”, Journal of Energy Technologies and Policy, ISSN 2224-3232, Vol.2, No.2, 2012.
  [2].   T.F.Chan, K.A.Nigim, L.L.Lai, “ Voltage and frequency control of self excited slip ring induction generators”IEEE Trans,
         Energy Conversion vol 19, pp. 81-87, March 2004.
  [3].   T.F.Chan “Analysis of self-excited induction generators using an iterative method” IEEE Trans. Energy Conversion, vol 10, pp.
         502-507, Sept .1995.
  [4].   E.G.Marra and J. A. Pomilio, “Induction – generator –based system providing regulated voltage with constant frequency”, IEEE
         Trans.Ind.Electron., vol.47,pp.908-914.Aug.2000.
  [5].   E.suarez and G. Bortolotto, “ Voltage- Frequency control of a self –excited Induction generator”,IEEE Trans. Energy
         conversion.vol.14,pp .394-401.Sep . 1999.

                                                                34
Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method

  [6].    Mustafa Al-saffar and Eui-cheol , “Controlled shunt capacitor self excited induction generator”, in proc.33rd IEEE
          Ind.applicate.soc.Annu.Meeting, vol.2, pp.1486-1490. 1998.
  [7].     K.A.Nigim, “ Static exciter for wound rotor induction machine”, in Proc.conf.rec.16 th Ind.applicat.Soc.Annu.Meeting, vol.2,
          pp.934-937. 1990.
  [8].    F.Girand and Z.M.Sa;meh “ Wind –driven , Variable- speed variable –frequency, double –output induction generator” Elect
          March power sys vol 26, pp 287-297,1998.
  [9].    S.S. Murthy. O.P. Malik and A.L.Tandon, “Analysis of self-excited induction generation” Procc . Inst. Eng…pt C, vol 129, No 6,
          pp260-265. Nov 1982.
  [10].   L.Ouazance and G.McPJherson , Jr “Analysis of the isolated induction generator” IEEE Trans, Power App Sys, vol PAS-102 pp
          2793-2798 Aug 1983.
  [11].   L.Shridhar, Bhim Singh and C.S. Jha,"Improvement in the Characteristics of Self Excited Induction Generator", Paper no. 92
          WM 02 0-8 EC, Presented at IEEE PES Winter Meeting. New York, 1992.
  [12].   S.S. Murthy, O.P. Malik and A.K. Tandon, "Analysis of self-excited induction generators", heedings of ZEE, Vol. l29, Part C,
          No. 6, pp.260-265, November 1982.
  [13].   Bhim Singh, R.K. Mishra and M.K.Vasantha, "Voltage Regulator for .Isolated Self Excited Cage Generators", to appear in
          Journal of Electric Power System Research, vol 24, no.2, pp. 75-83, 1992.
  [14].   N.H. Malik and AA. Mazi, "Capacitance requirements for isolated self excited induction generators", ZEEE Trenscrcticmr on
          Energy caulversion, Vol. EC-2, No. 1, pp. 62-68, March 1987.
  [15].   Chan, T.F, Nigim, K.A., Lai, L.L. “Voltage and frequency control of self-excited slip-ring induction generators”, Energy
          Conversion, IEEE Transactions ,March 2004, Dept. of Electr. Eng., Hong Kong Polytech. Univ., China Vol.19 , Issue: 1, pp. 81
          – 87.
  [16].   Swati Devabhaktuni, S.V.Jayaram kumar, “Performance Analysis of Wind Turbine Driven Self-Excited Induction Generator
          with External Rotor Capacitance”, International Journal of Advanced Engineering Sciences AND Technologies, Vol.10, Issue
          No. 1, pp. 001 – 006.
  [17].   S. Wekhande and V. Agarwal (1999), “A new variable speed constant voltage controller for self-excited induction generator with
          minimum control requirements,” Proceedings on Power Electronics and Drives Systems Conference vol. 1, pp. 98 – 103.
  [18].   Olorunfemi Ojo, "The transient and qualitative performance of a self-excited single-phase induction generator,"Paper no. 95WM-
          075-EC, to appear in IEEE ?Irans. onEnergy con version, 1995.
  [19].   M. B. Brennen and A. Abbondati, "Static exciter induction generator," IEEE ?Irans. OD Industry Applications,Vol. IAS-13, No.
          5, pp. 422-428, 1977.
  [20].   Yaser Anagreh (2001), “Steady state performance of series DC motor powered by wind driven self-excited induction generator,”
          Proceedings on Rev. Energ. Ren: power Engineering, pp.9-15.
  [21].   Rajambal and C.Chellamuthu (2002), “Modeling and simulation of grid connected wind electric generating system,” Proceedings
          on IEEE region conference TENCON. Pp 1847 – 1852. vol. 3.

                                                         APPENDIX -I
CONSTANTS:
 f0=(-b*XC*X2+XL*XC-b*XL*XC-b*R1*RL-b*X1*XC);
 f1=(-b*X2*XL*XC-b*X2*R1*RL-b*X2*X1*XC);
 f2=(RL*R2+XC*X2+R1*RL+X1*XC);
f3=(X2*XL*XC+X2*R1*RL+X2*X1*XC+X1*RL*R2+XL*R1*R2);
 f4=(b*XL*X2+b*X1*XL);
 f5=(b*X1*XL*X2);
 f6=(-XL*X2-X1*XL);
 f7=(X1*XL*X2);
 f8=(-RL*R2*XC);
 g0=(-XC*R2-RL*XC-R1*XC);
 g1=(-R2*XL*XC-R1*RL*R2-R2*X1*XC-X2*RL*XC-X2*R1*XC);
 g2=(-b*X2*RL-b*X1*RL-b*XL*R1);
 g3=(-b*X2*X1*RL-b*X2*XL*R1);
 g4=(XL*R2+X2*RL+X1*RL+XL*R1);
 g5=(XL*X1*R2+X2*X1*RL+X2*XL*R1);
 g6=(b*RL*XC+b*R1*XC);
 g7=(b*X2*RL*XC+b*X2*R1*XC);

                                                        APPENDIX –II
INDUCTION MACHINE PARAMETERS:
Number of phases =3
Number of poles =4
Frequency        =50 Hz
Voltage          =380V
Current          =4.5A
Power            =1.8 KW
Connection       =star
Type             =slip-ring
R1               =0.0597 p.u
X1               =0.118 p.u
R2               =0.0982 p.u
X2               =0.118 p.u

                                                                 35

Weitere ähnliche Inhalte

Was ist angesagt?

射頻電子 - [第三章] 史密斯圖與阻抗匹配
射頻電子 - [第三章] 史密斯圖與阻抗匹配射頻電子 - [第三章] 史密斯圖與阻抗匹配
射頻電子 - [第三章] 史密斯圖與阻抗匹配Simen Li
 
Ee2251 em-i
Ee2251 em-iEe2251 em-i
Ee2251 em-isannbhu
 
20120214 optical pulse_measurement_wei-yi
20120214 optical pulse_measurement_wei-yi20120214 optical pulse_measurement_wei-yi
20120214 optical pulse_measurement_wei-yi奕勳 陳
 
Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...
Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...
Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...IDES Editor
 
ADF4113 Frequency Synthesizer 驅動程式實作
ADF4113 Frequency Synthesizer 驅動程式實作ADF4113 Frequency Synthesizer 驅動程式實作
ADF4113 Frequency Synthesizer 驅動程式實作Simen Li
 
ECNG 6509 Switchgear Technology
ECNG 6509    Switchgear TechnologyECNG 6509    Switchgear Technology
ECNG 6509 Switchgear TechnologyChandrabhan Sharma
 
COMBINED SKEWED CMOS RING OSCILLATOR
COMBINED SKEWED CMOS RING OSCILLATORCOMBINED SKEWED CMOS RING OSCILLATOR
COMBINED SKEWED CMOS RING OSCILLATORecij
 

Was ist angesagt? (9)

射頻電子 - [第三章] 史密斯圖與阻抗匹配
射頻電子 - [第三章] 史密斯圖與阻抗匹配射頻電子 - [第三章] 史密斯圖與阻抗匹配
射頻電子 - [第三章] 史密斯圖與阻抗匹配
 
Ee2251 em-i
Ee2251 em-iEe2251 em-i
Ee2251 em-i
 
20120214 optical pulse_measurement_wei-yi
20120214 optical pulse_measurement_wei-yi20120214 optical pulse_measurement_wei-yi
20120214 optical pulse_measurement_wei-yi
 
Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...
Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...
Minimum Component Based First-Order All- Pass Filter with Inverting and Non-i...
 
Transmission Line
Transmission LineTransmission Line
Transmission Line
 
ADF4113 Frequency Synthesizer 驅動程式實作
ADF4113 Frequency Synthesizer 驅動程式實作ADF4113 Frequency Synthesizer 驅動程式實作
ADF4113 Frequency Synthesizer 驅動程式實作
 
ECNG 6509 Switchgear Technology
ECNG 6509    Switchgear TechnologyECNG 6509    Switchgear Technology
ECNG 6509 Switchgear Technology
 
COMBINED SKEWED CMOS RING OSCILLATOR
COMBINED SKEWED CMOS RING OSCILLATORCOMBINED SKEWED CMOS RING OSCILLATOR
COMBINED SKEWED CMOS RING OSCILLATOR
 
Jokyokai2
Jokyokai2Jokyokai2
Jokyokai2
 

Andere mochten auch

IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 

Andere mochten auch (9)

IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 

Ähnlich wie IJERD (www.ijerd.com) International Journal of Engineering Research and Development

Scherbius drive of electrical machines
Scherbius drive of electrical machinesScherbius drive of electrical machines
Scherbius drive of electrical machinesemredurna
 
Voltage Oriented Decoupled Control Scheme for DFIG’s Grid Side Converter
Voltage Oriented Decoupled Control Scheme for DFIG’s Grid Side ConverterVoltage Oriented Decoupled Control Scheme for DFIG’s Grid Side Converter
Voltage Oriented Decoupled Control Scheme for DFIG’s Grid Side ConverterTELKOMNIKA JOURNAL
 
Dynamic response of wound rotor induction generator for wind energy application
Dynamic response of wound rotor induction generator for wind energy applicationDynamic response of wound rotor induction generator for wind energy application
Dynamic response of wound rotor induction generator for wind energy applicationAlexander Decker
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD Editor
 
Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...
Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...
Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...IDES Editor
 
The Self Excited Induction Generator with Observation Magnetizing Characteris...
The Self Excited Induction Generator with Observation Magnetizing Characteris...The Self Excited Induction Generator with Observation Magnetizing Characteris...
The Self Excited Induction Generator with Observation Magnetizing Characteris...IJPEDS-IAES
 
The Neural Network-Combined Optimal Control System of Induction Motor
The Neural Network-Combined Optimal Control System of Induction MotorThe Neural Network-Combined Optimal Control System of Induction Motor
The Neural Network-Combined Optimal Control System of Induction MotorIJECEIAES
 
02 1 synchronous-machines
02 1 synchronous-machines02 1 synchronous-machines
02 1 synchronous-machineshuseyin28
 
射頻電子 - [第六章] 低雜訊放大器設計
射頻電子 - [第六章] 低雜訊放大器設計射頻電子 - [第六章] 低雜訊放大器設計
射頻電子 - [第六章] 低雜訊放大器設計Simen Li
 
Eh4 energy harvesting due to random excitations and optimal design
Eh4   energy harvesting due to random excitations and optimal designEh4   energy harvesting due to random excitations and optimal design
Eh4 energy harvesting due to random excitations and optimal designUniversity of Glasgow
 
Master slave vector controlled double induction motor using unity power facto...
Master slave vector controlled double induction motor using unity power facto...Master slave vector controlled double induction motor using unity power facto...
Master slave vector controlled double induction motor using unity power facto...eSAT Journals
 

Ähnlich wie IJERD (www.ijerd.com) International Journal of Engineering Research and Development (20)

Scherbius drive of electrical machines
Scherbius drive of electrical machinesScherbius drive of electrical machines
Scherbius drive of electrical machines
 
Voltage Oriented Decoupled Control Scheme for DFIG’s Grid Side Converter
Voltage Oriented Decoupled Control Scheme for DFIG’s Grid Side ConverterVoltage Oriented Decoupled Control Scheme for DFIG’s Grid Side Converter
Voltage Oriented Decoupled Control Scheme for DFIG’s Grid Side Converter
 
Dynamic response of wound rotor induction generator for wind energy application
Dynamic response of wound rotor induction generator for wind energy applicationDynamic response of wound rotor induction generator for wind energy application
Dynamic response of wound rotor induction generator for wind energy application
 
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
IJERD (www.ijerd.com) International Journal of Engineering Research and Devel...
 
JSAEM
JSAEMJSAEM
JSAEM
 
Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...
Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...
Analysis of Self-Excited Induction Generator under Balanced or Unbalanced Con...
 
The Self Excited Induction Generator with Observation Magnetizing Characteris...
The Self Excited Induction Generator with Observation Magnetizing Characteris...The Self Excited Induction Generator with Observation Magnetizing Characteris...
The Self Excited Induction Generator with Observation Magnetizing Characteris...
 
The Neural Network-Combined Optimal Control System of Induction Motor
The Neural Network-Combined Optimal Control System of Induction MotorThe Neural Network-Combined Optimal Control System of Induction Motor
The Neural Network-Combined Optimal Control System of Induction Motor
 
02 1 synchronous-machines
02 1 synchronous-machines02 1 synchronous-machines
02 1 synchronous-machines
 
Gn2511881192
Gn2511881192Gn2511881192
Gn2511881192
 
Gn2511881192
Gn2511881192Gn2511881192
Gn2511881192
 
射頻電子 - [第六章] 低雜訊放大器設計
射頻電子 - [第六章] 低雜訊放大器設計射頻電子 - [第六章] 低雜訊放大器設計
射頻電子 - [第六章] 低雜訊放大器設計
 
SKM100GB173D
SKM100GB173DSKM100GB173D
SKM100GB173D
 
Eh4 energy harvesting due to random excitations and optimal design
Eh4   energy harvesting due to random excitations and optimal designEh4   energy harvesting due to random excitations and optimal design
Eh4 energy harvesting due to random excitations and optimal design
 
Double star induction machine using nonlinear integral backstepping control
Double star induction machine using nonlinear integral backstepping controlDouble star induction machine using nonlinear integral backstepping control
Double star induction machine using nonlinear integral backstepping control
 
Ci33514517
Ci33514517Ci33514517
Ci33514517
 
Ci33514517
Ci33514517Ci33514517
Ci33514517
 
Ci33514517
Ci33514517Ci33514517
Ci33514517
 
Article 1
Article 1Article 1
Article 1
 
Master slave vector controlled double induction motor using unity power facto...
Master slave vector controlled double induction motor using unity power facto...Master slave vector controlled double induction motor using unity power facto...
Master slave vector controlled double induction motor using unity power facto...
 

Mehr von IJERD Editor

A Novel Method for Prevention of Bandwidth Distributed Denial of Service Attacks
A Novel Method for Prevention of Bandwidth Distributed Denial of Service AttacksA Novel Method for Prevention of Bandwidth Distributed Denial of Service Attacks
A Novel Method for Prevention of Bandwidth Distributed Denial of Service AttacksIJERD Editor
 
MEMS MICROPHONE INTERFACE
MEMS MICROPHONE INTERFACEMEMS MICROPHONE INTERFACE
MEMS MICROPHONE INTERFACEIJERD Editor
 
Influence of tensile behaviour of slab on the structural Behaviour of shear c...
Influence of tensile behaviour of slab on the structural Behaviour of shear c...Influence of tensile behaviour of slab on the structural Behaviour of shear c...
Influence of tensile behaviour of slab on the structural Behaviour of shear c...IJERD Editor
 
Gold prospecting using Remote Sensing ‘A case study of Sudan’
Gold prospecting using Remote Sensing ‘A case study of Sudan’Gold prospecting using Remote Sensing ‘A case study of Sudan’
Gold prospecting using Remote Sensing ‘A case study of Sudan’IJERD Editor
 
Reducing Corrosion Rate by Welding Design
Reducing Corrosion Rate by Welding DesignReducing Corrosion Rate by Welding Design
Reducing Corrosion Rate by Welding DesignIJERD Editor
 
Router 1X3 – RTL Design and Verification
Router 1X3 – RTL Design and VerificationRouter 1X3 – RTL Design and Verification
Router 1X3 – RTL Design and VerificationIJERD Editor
 
Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...
Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...
Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...IJERD Editor
 
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVR
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVRMitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVR
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVRIJERD Editor
 
Study on the Fused Deposition Modelling In Additive Manufacturing
Study on the Fused Deposition Modelling In Additive ManufacturingStudy on the Fused Deposition Modelling In Additive Manufacturing
Study on the Fused Deposition Modelling In Additive ManufacturingIJERD Editor
 
Spyware triggering system by particular string value
Spyware triggering system by particular string valueSpyware triggering system by particular string value
Spyware triggering system by particular string valueIJERD Editor
 
A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...
A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...
A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...IJERD Editor
 
Secure Image Transmission for Cloud Storage System Using Hybrid Scheme
Secure Image Transmission for Cloud Storage System Using Hybrid SchemeSecure Image Transmission for Cloud Storage System Using Hybrid Scheme
Secure Image Transmission for Cloud Storage System Using Hybrid SchemeIJERD Editor
 
Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...
Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...
Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...IJERD Editor
 
Gesture Gaming on the World Wide Web Using an Ordinary Web Camera
Gesture Gaming on the World Wide Web Using an Ordinary Web CameraGesture Gaming on the World Wide Web Using an Ordinary Web Camera
Gesture Gaming on the World Wide Web Using an Ordinary Web CameraIJERD Editor
 
Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...
Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...
Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...IJERD Editor
 
Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...
Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...
Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...IJERD Editor
 
Moon-bounce: A Boon for VHF Dxing
Moon-bounce: A Boon for VHF DxingMoon-bounce: A Boon for VHF Dxing
Moon-bounce: A Boon for VHF DxingIJERD Editor
 
“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...
“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...
“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...IJERD Editor
 
Importance of Measurements in Smart Grid
Importance of Measurements in Smart GridImportance of Measurements in Smart Grid
Importance of Measurements in Smart GridIJERD Editor
 
Study of Macro level Properties of SCC using GGBS and Lime stone powder
Study of Macro level Properties of SCC using GGBS and Lime stone powderStudy of Macro level Properties of SCC using GGBS and Lime stone powder
Study of Macro level Properties of SCC using GGBS and Lime stone powderIJERD Editor
 

Mehr von IJERD Editor (20)

A Novel Method for Prevention of Bandwidth Distributed Denial of Service Attacks
A Novel Method for Prevention of Bandwidth Distributed Denial of Service AttacksA Novel Method for Prevention of Bandwidth Distributed Denial of Service Attacks
A Novel Method for Prevention of Bandwidth Distributed Denial of Service Attacks
 
MEMS MICROPHONE INTERFACE
MEMS MICROPHONE INTERFACEMEMS MICROPHONE INTERFACE
MEMS MICROPHONE INTERFACE
 
Influence of tensile behaviour of slab on the structural Behaviour of shear c...
Influence of tensile behaviour of slab on the structural Behaviour of shear c...Influence of tensile behaviour of slab on the structural Behaviour of shear c...
Influence of tensile behaviour of slab on the structural Behaviour of shear c...
 
Gold prospecting using Remote Sensing ‘A case study of Sudan’
Gold prospecting using Remote Sensing ‘A case study of Sudan’Gold prospecting using Remote Sensing ‘A case study of Sudan’
Gold prospecting using Remote Sensing ‘A case study of Sudan’
 
Reducing Corrosion Rate by Welding Design
Reducing Corrosion Rate by Welding DesignReducing Corrosion Rate by Welding Design
Reducing Corrosion Rate by Welding Design
 
Router 1X3 – RTL Design and Verification
Router 1X3 – RTL Design and VerificationRouter 1X3 – RTL Design and Verification
Router 1X3 – RTL Design and Verification
 
Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...
Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...
Active Power Exchange in Distributed Power-Flow Controller (DPFC) At Third Ha...
 
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVR
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVRMitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVR
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVR
 
Study on the Fused Deposition Modelling In Additive Manufacturing
Study on the Fused Deposition Modelling In Additive ManufacturingStudy on the Fused Deposition Modelling In Additive Manufacturing
Study on the Fused Deposition Modelling In Additive Manufacturing
 
Spyware triggering system by particular string value
Spyware triggering system by particular string valueSpyware triggering system by particular string value
Spyware triggering system by particular string value
 
A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...
A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...
A Blind Steganalysis on JPEG Gray Level Image Based on Statistical Features a...
 
Secure Image Transmission for Cloud Storage System Using Hybrid Scheme
Secure Image Transmission for Cloud Storage System Using Hybrid SchemeSecure Image Transmission for Cloud Storage System Using Hybrid Scheme
Secure Image Transmission for Cloud Storage System Using Hybrid Scheme
 
Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...
Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...
Application of Buckley-Leverett Equation in Modeling the Radius of Invasion i...
 
Gesture Gaming on the World Wide Web Using an Ordinary Web Camera
Gesture Gaming on the World Wide Web Using an Ordinary Web CameraGesture Gaming on the World Wide Web Using an Ordinary Web Camera
Gesture Gaming on the World Wide Web Using an Ordinary Web Camera
 
Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...
Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...
Hardware Analysis of Resonant Frequency Converter Using Isolated Circuits And...
 
Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...
Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...
Simulated Analysis of Resonant Frequency Converter Using Different Tank Circu...
 
Moon-bounce: A Boon for VHF Dxing
Moon-bounce: A Boon for VHF DxingMoon-bounce: A Boon for VHF Dxing
Moon-bounce: A Boon for VHF Dxing
 
“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...
“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...
“MS-Extractor: An Innovative Approach to Extract Microsatellites on „Y‟ Chrom...
 
Importance of Measurements in Smart Grid
Importance of Measurements in Smart GridImportance of Measurements in Smart Grid
Importance of Measurements in Smart Grid
 
Study of Macro level Properties of SCC using GGBS and Lime stone powder
Study of Macro level Properties of SCC using GGBS and Lime stone powderStudy of Macro level Properties of SCC using GGBS and Lime stone powder
Study of Macro level Properties of SCC using GGBS and Lime stone powder
 

Kürzlich hochgeladen

Crea il tuo assistente AI con lo Stregatto (open source python framework)
Crea il tuo assistente AI con lo Stregatto (open source python framework)Crea il tuo assistente AI con lo Stregatto (open source python framework)
Crea il tuo assistente AI con lo Stregatto (open source python framework)Commit University
 
activity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdf
activity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdf
activity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdfJamie (Taka) Wang
 
99.99% of Your Traces Are (Probably) Trash (SRECon NA 2024).pdf
99.99% of Your Traces  Are (Probably) Trash (SRECon NA 2024).pdf99.99% of Your Traces  Are (Probably) Trash (SRECon NA 2024).pdf
99.99% of Your Traces Are (Probably) Trash (SRECon NA 2024).pdfPaige Cruz
 
Using IESVE for Loads, Sizing and Heat Pump Modeling to Achieve Decarbonization
Using IESVE for Loads, Sizing and Heat Pump Modeling to Achieve DecarbonizationUsing IESVE for Loads, Sizing and Heat Pump Modeling to Achieve Decarbonization
Using IESVE for Loads, Sizing and Heat Pump Modeling to Achieve DecarbonizationIES VE
 
Valere | Digital Solutions & AI Transformation Portfolio | 2024
Valere | Digital Solutions & AI Transformation Portfolio | 2024Valere | Digital Solutions & AI Transformation Portfolio | 2024
Valere | Digital Solutions & AI Transformation Portfolio | 2024Alexander Turgeon
 
Igniting Next Level Productivity with AI-Infused Data Integration Workflows
Igniting Next Level Productivity with AI-Infused Data Integration WorkflowsIgniting Next Level Productivity with AI-Infused Data Integration Workflows
Igniting Next Level Productivity with AI-Infused Data Integration WorkflowsSafe Software
 
Secure your environment with UiPath and CyberArk technologies - Session 1
Secure your environment with UiPath and CyberArk technologies - Session 1Secure your environment with UiPath and CyberArk technologies - Session 1
Secure your environment with UiPath and CyberArk technologies - Session 1DianaGray10
 
UiPath Solutions Management Preview - Northern CA Chapter - March 22.pdf
UiPath Solutions Management Preview - Northern CA Chapter - March 22.pdfUiPath Solutions Management Preview - Northern CA Chapter - March 22.pdf
UiPath Solutions Management Preview - Northern CA Chapter - March 22.pdfDianaGray10
 
IEEE Computer Society’s Strategic Activities and Products including SWEBOK Guide
IEEE Computer Society’s Strategic Activities and Products including SWEBOK GuideIEEE Computer Society’s Strategic Activities and Products including SWEBOK Guide
IEEE Computer Society’s Strategic Activities and Products including SWEBOK GuideHironori Washizaki
 
Artificial Intelligence & SEO Trends for 2024
Artificial Intelligence & SEO Trends for 2024Artificial Intelligence & SEO Trends for 2024
Artificial Intelligence & SEO Trends for 2024D Cloud Solutions
 
Nanopower In Semiconductor Industry.pdf
Nanopower  In Semiconductor Industry.pdfNanopower  In Semiconductor Industry.pdf
Nanopower In Semiconductor Industry.pdfPedro Manuel
 
IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019
IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019
IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019IES VE
 
UiPath Studio Web workshop series - Day 7
UiPath Studio Web workshop series - Day 7UiPath Studio Web workshop series - Day 7
UiPath Studio Web workshop series - Day 7DianaGray10
 
COMPUTER 10 Lesson 8 - Building a Website
COMPUTER 10 Lesson 8 - Building a WebsiteCOMPUTER 10 Lesson 8 - Building a Website
COMPUTER 10 Lesson 8 - Building a Websitedgelyza
 
All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...
All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...
All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...Daniel Zivkovic
 
COMPUTER 10: Lesson 7 - File Storage and Online Collaboration
COMPUTER 10: Lesson 7 - File Storage and Online CollaborationCOMPUTER 10: Lesson 7 - File Storage and Online Collaboration
COMPUTER 10: Lesson 7 - File Storage and Online Collaborationbruanjhuli
 
UiPath Studio Web workshop series - Day 8
UiPath Studio Web workshop series - Day 8UiPath Studio Web workshop series - Day 8
UiPath Studio Web workshop series - Day 8DianaGray10
 
Computer 10: Lesson 10 - Online Crimes and Hazards
Computer 10: Lesson 10 - Online Crimes and HazardsComputer 10: Lesson 10 - Online Crimes and Hazards
Computer 10: Lesson 10 - Online Crimes and HazardsSeth Reyes
 
OpenShift Commons Paris - Choose Your Own Observability Adventure
OpenShift Commons Paris - Choose Your Own Observability AdventureOpenShift Commons Paris - Choose Your Own Observability Adventure
OpenShift Commons Paris - Choose Your Own Observability AdventureEric D. Schabell
 
The Kubernetes Gateway API and its role in Cloud Native API Management
The Kubernetes Gateway API and its role in Cloud Native API ManagementThe Kubernetes Gateway API and its role in Cloud Native API Management
The Kubernetes Gateway API and its role in Cloud Native API ManagementNuwan Dias
 

Kürzlich hochgeladen (20)

Crea il tuo assistente AI con lo Stregatto (open source python framework)
Crea il tuo assistente AI con lo Stregatto (open source python framework)Crea il tuo assistente AI con lo Stregatto (open source python framework)
Crea il tuo assistente AI con lo Stregatto (open source python framework)
 
activity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdf
activity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdf
activity_diagram_combine_v4_20190827.pdfactivity_diagram_combine_v4_20190827.pdf
 
99.99% of Your Traces Are (Probably) Trash (SRECon NA 2024).pdf
99.99% of Your Traces  Are (Probably) Trash (SRECon NA 2024).pdf99.99% of Your Traces  Are (Probably) Trash (SRECon NA 2024).pdf
99.99% of Your Traces Are (Probably) Trash (SRECon NA 2024).pdf
 
Using IESVE for Loads, Sizing and Heat Pump Modeling to Achieve Decarbonization
Using IESVE for Loads, Sizing and Heat Pump Modeling to Achieve DecarbonizationUsing IESVE for Loads, Sizing and Heat Pump Modeling to Achieve Decarbonization
Using IESVE for Loads, Sizing and Heat Pump Modeling to Achieve Decarbonization
 
Valere | Digital Solutions & AI Transformation Portfolio | 2024
Valere | Digital Solutions & AI Transformation Portfolio | 2024Valere | Digital Solutions & AI Transformation Portfolio | 2024
Valere | Digital Solutions & AI Transformation Portfolio | 2024
 
Igniting Next Level Productivity with AI-Infused Data Integration Workflows
Igniting Next Level Productivity with AI-Infused Data Integration WorkflowsIgniting Next Level Productivity with AI-Infused Data Integration Workflows
Igniting Next Level Productivity with AI-Infused Data Integration Workflows
 
Secure your environment with UiPath and CyberArk technologies - Session 1
Secure your environment with UiPath and CyberArk technologies - Session 1Secure your environment with UiPath and CyberArk technologies - Session 1
Secure your environment with UiPath and CyberArk technologies - Session 1
 
UiPath Solutions Management Preview - Northern CA Chapter - March 22.pdf
UiPath Solutions Management Preview - Northern CA Chapter - March 22.pdfUiPath Solutions Management Preview - Northern CA Chapter - March 22.pdf
UiPath Solutions Management Preview - Northern CA Chapter - March 22.pdf
 
IEEE Computer Society’s Strategic Activities and Products including SWEBOK Guide
IEEE Computer Society’s Strategic Activities and Products including SWEBOK GuideIEEE Computer Society’s Strategic Activities and Products including SWEBOK Guide
IEEE Computer Society’s Strategic Activities and Products including SWEBOK Guide
 
Artificial Intelligence & SEO Trends for 2024
Artificial Intelligence & SEO Trends for 2024Artificial Intelligence & SEO Trends for 2024
Artificial Intelligence & SEO Trends for 2024
 
Nanopower In Semiconductor Industry.pdf
Nanopower  In Semiconductor Industry.pdfNanopower  In Semiconductor Industry.pdf
Nanopower In Semiconductor Industry.pdf
 
IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019
IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019
IESVE Software for Florida Code Compliance Using ASHRAE 90.1-2019
 
UiPath Studio Web workshop series - Day 7
UiPath Studio Web workshop series - Day 7UiPath Studio Web workshop series - Day 7
UiPath Studio Web workshop series - Day 7
 
COMPUTER 10 Lesson 8 - Building a Website
COMPUTER 10 Lesson 8 - Building a WebsiteCOMPUTER 10 Lesson 8 - Building a Website
COMPUTER 10 Lesson 8 - Building a Website
 
All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...
All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...
All in AI: LLM Landscape & RAG in 2024 with Mark Ryan (Google) & Jerry Liu (L...
 
COMPUTER 10: Lesson 7 - File Storage and Online Collaboration
COMPUTER 10: Lesson 7 - File Storage and Online CollaborationCOMPUTER 10: Lesson 7 - File Storage and Online Collaboration
COMPUTER 10: Lesson 7 - File Storage and Online Collaboration
 
UiPath Studio Web workshop series - Day 8
UiPath Studio Web workshop series - Day 8UiPath Studio Web workshop series - Day 8
UiPath Studio Web workshop series - Day 8
 
Computer 10: Lesson 10 - Online Crimes and Hazards
Computer 10: Lesson 10 - Online Crimes and HazardsComputer 10: Lesson 10 - Online Crimes and Hazards
Computer 10: Lesson 10 - Online Crimes and Hazards
 
OpenShift Commons Paris - Choose Your Own Observability Adventure
OpenShift Commons Paris - Choose Your Own Observability AdventureOpenShift Commons Paris - Choose Your Own Observability Adventure
OpenShift Commons Paris - Choose Your Own Observability Adventure
 
The Kubernetes Gateway API and its role in Cloud Native API Management
The Kubernetes Gateway API and its role in Cloud Native API ManagementThe Kubernetes Gateway API and its role in Cloud Native API Management
The Kubernetes Gateway API and its role in Cloud Native API Management
 

IJERD (www.ijerd.com) International Journal of Engineering Research and Development

  • 1. International Journal of Engineering Research and Development e-ISSN : 2278-067X, p-ISSN : 2278-800X, www.ijerd.com Volume 2, Issue 7 (August 2012), PP. 26-35 Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method S.Mathankumar1, P.Loganathan2 1, 2 Assistant Professor, Department of Electrical & Electronics Engineering, V.M.K.V.Engineering College, Vinayaka Missions University, Salem, Tamil Nadu, India -636 308. Abstract––In this paper deals with steady state analysis of self-excited slip ring induction generator (SESRIG) is performed using Newton- Raphson method. By varying effective rotor resistance of a self excited slip ring induction generator, the magnitude and frequency of the output voltage can be controlled over a wide speed range. A steady state analysis based on normalized equivalent circuit enables the control characteristics to be deduced. In the wind driven SESRIG system the rotor speed is varied along with wind speed. For a given stator load, both frequency and voltage can be maintained constant as speed is varied by changing rotor resistance, with constant excitation capacitance. The proposed scheme may be used in low cost variable speed wind energy system for providing good quality electric power to remote regions. Keywords––SESRIG, Newton- Raphson Method, Rotor Resistance I. INTRODUCTION Self-excitation in an induction generator occurs when the rotor is driven by a Prime mover and a suitable capacitance is connected across the stator terminals. Under such conditions, the terminal capacitance furnishes the lagging reactive power necessary for establishing the air gap flux and the machine is often referred to as a self-excited induction generator (SEIG). SEIGs increasingly utilized in stand-alone generation systems that employ wind or hydro power. Unlike introduction generators connected to the power utility grid, both the frequency and the terminal voltage of the SEIG vary with load even when the rotor speed is maintained constant. An increase in the rotor speed will result in a proportionate increase in frequency, often accompanied by severe over voltage and excessive current. Recently, there has been rigorous research on the voltage and frequency control of squirrel – cage type SEIGs, but relatively little research efforts have been devoted to the use of the slip ring induction machine for generator applications. a. Advantages  When a grid connection is permissible, the slip-ring machine may be operated as a double-output induction generator (DOIG) using the slip-energy recovery technique.  In the case of a self-excited slip-ring induction generator (SESRIG), the system cost can be further reduced by the use of a simple rotor resistance controller.  Only a capacitor bank needs to be connected to the stator terminals, the SESRIG provides a good quality ac source with little harmonic distortion to the stator load.  Advantageous feature of the SESRIG is that independent control of the voltage and frequency can be achieved easily. Even with a wide variation in speed, the generator frequency can be maintained reasonably constant by rotor resistance control, while the voltage can be controlled by varying the excitation capacitance.  Although the slip-ring machine is more expensive and requires more maintenance, it permits rotor slip-power control when driven by a variable-speed turbine. II. CIRCUIT ARRANGEMENT . Slip-ring RX2 induction ZL machine ZL RX2 ZL c c RX2 Turbine Fig. 2.1. The circuit arrangement of a three phase SESRIG 26
  • 2. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method In this paper, the voltage and frequency control of a three phase SESRIG by variation of external rotor resistance will be investigated. Based on a normalized equivalent circuit model, the frequency and voltage characteristics are deduced and experimental results are presented to verify the feasibility of the control method. Practical implementation of a closed loop scheme that uses chopper-controlled rotor resistance will also be described. Fig. 2.1 shows the circuit arrangement of a three phase SESRIG. The excitation capacitance „C‟ is required for initiating voltage buildup and maintaining the output voltage. It is noticed that the electrical output power is dissipated in both the stator impedance ZL as well as the external rotor resistance RX2. Hence, the machine may also be regarded as a DOIG if the power is Rx2 is effectively utilized. III. MATHEMATICAL MODELING 3.1. Equivalent circuit analysis of SESRIG The SESRIG is actually an induction motor that driven by a prime mover while its stator excitation provided by an external capacitor connected to the stator. The excitation capacitance is required for initiating voltage buildup and maintaining the output voltage. Figure.3.1 Per-phase Equivalent circuit of SESRIG Fig 3.1 Shows the per phase equivalent circuit of SESRIG where the rotor resistance R2 is the sum of the rotor winding resistance and external rotor resistance. The circuit has been normalized to the base (rated) frequency through the introduction of the per- unit frequency „a‟ and the per-unit speed „b‟. Various methods have been developed for solution of the SESRIG equivalent circuit. Adopting the nodal admittance, the following relation ship may be established for successful voltage build-up. 3.2. Nodal admittance method This method considers the admittances connected across the nodes which define the air gap. By equating the sum of real parts to zero (which is equivalent to active power balance), a polynomial in “a” is obtained. Xm can be determined upon equating the sum of imaginary parts to zero, using the value of “a” obtained after solving the polynomial. Yt+Ym+Y2=0 (1) Where, 1 1 Yt    G t  jBt (2) zt Zac  Zab 1 Ym   j  G m  jBt (3) Xm 1 Y2   G m  jBt (4) R2  jX 2 ab Equating the real and imaginary parts in 1 to zero respectively, the following equations in real number are obtained. Gt+Gm+G2 = 0 (5) Bt+Bm+B2 = 0 (6) REAL PARTS(Gt+Gm+G2 )= -aXmbXCX2+ aXmXLXC- aXmbXLXC- aXmbR1RL- aXmbX1XC- abX2XLXC- abX2R1RL- abX2X1*XC +a2XmRLR2+ a2XmXCX2+ a2XmR1RL+ a2XmX1XC+ a2X2XLXC+ a2X2R1RL+ a2X2X1XC+ a2X1RLR2+ a2XLR1R2 +a3XmbXLX2+ a3XmbX1XL+a2bX1XLX2- a4XmXLX2-a4XmX1XL+a4X1XLX2-RLR2XC (7) 27
  • 3. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method IMAGINARY PARTS(Bt+Bm+B2 )= aXmXCR2- aXmRLXC- aXmR1XC - aR2XLXC- aR1RLR2- aR2X1XC- aX2RLXC- aX2R1XC- a2XmbX2RL-a2XmbX1RL-a2XmbXLR1-a2bX2X1RL- a2bX2XLR1+ a3XmXLR2+ a3XmX2RL+ a3XmX1RL+ a3XmXLR1 +a3XLX1R2+ a3X2X1RL+ a3X2XLR1+ XmbRLXC+ XmbR1XC+ bX2RLXC +bX2R1XC (8) 3.3. Newton-Raphson method By taking the Coefficients a and Xm in the equations(7), (8) the real and imaginary parts can be given by 2 h1  ( f 0 X m  f1 ) a  ( f 2 X m  f 3 ) a  (9) 3 4 ( f 4 X m  f 5) a  ( f 6 X m  f 7 ) a  f 8 2 h 2  ( g 0 X m  g1 ) a  ( g 2 X m  g 3 ) a (10) 3 4  ( g 4 X m  g 5) a  ( g 6 X m  g 7 )a  g8 The constants are given in appendix A-1. h1  ( f 0 X m  f1 )  2( f 2 X m  f 3 ) a  a (11) 2 3( f 4 X m  f 5 ) a  4( f 6 X m  f 7 ) a 3 h 2  ( g 0 X m  g1 )  2( g 2 X m  g 3 ) a  a (12) 2 3( g 4 X m  g 5 ) a  4( g 6 X m  g 7 ) a 3 h1 2 3 4  f0 a  f2 a  f4 a  f6 a (13) X m h 2 2 3 4  g0a  g2a  g4a  g6a (14) X m The „J‟ matrix is given by  h1  h1  a X m    J   (15)    h 2 h 2   a  X m  From the equations (7) & (8), the matrix „K‟ is given by  h1  K     (16)  h 2  The inverse of „j‟ matrix is given by 1 1 J  adj[ J ] (17) J 28
  • 4. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method The value of a and X m is calculated by a  1 Xm  [ J ] [ K ] (18)   The value of „a‟ and „Xm‟ is calculated using -R method from equations (19) and (20). a new = a old + a (19) Xm new= Xm old + X m (20) The induction machine used here is given in appendix A-2 The air gap voltage E1 is expressed in terms of Xm by a piece wise linerized equation of the form. A stable operating point exists, provided that X m is less than the actuated value having determined all constants including Xm and El. The equivalent circuit of fig is complexly solved for the steady state performance of the induction generator. The stator phase current is given by E1 I1  (22) Z LC  Z 1 where, R1 Z1   jX 1 a R2 Z2   jX 2 ab RL ZL   jX L (23) a Xc Zc   j Z a Z LC  Z L // Z C The stator phase voltage is given by , V1= (IL*ZL*a) (24) Pout =3*IL2*RL (25) Where, IL= (I1*ZC)/ (ZL+ZC) (26) 3.4. Computational Algorithm 1. Read all the machine required parameters. 2. Determine the value of the constants given in appendix A-1. 3. Assume the initial value of a and Xm (a= b in p.u and Xm= saturated value in p.u). 4. Determine the value of real and imaginary terms given in equations (7) and (8). 5. If the value of h1 and h2 are greater than tolerance (0.0001)go to next Step otherwise go to step 11. 6. From the „K‟ matrix given in equation (16). 7. Determine the partial derivatives of h1 and h2 with respect to a and Xm given in equation (11), (12), (13) and (14). 8. Form „J‟ matrix and inverse of „J‟ matrix given in equ (15),(17)steps. 9. Determine the value of a and Xm given in equation (18). 10. Update the value of a and Xm given in the equation (19) and (20) and go to step 4. 11. Obtain the air gap voltage E1 expressed in terms of Xm given in equation (21). 12. Determine the stator phase current I1 given in equation (22). 13. Determine the stator phase voltage V1 and output power Pout given in equation (24) & (25). 14. Stop. 29
  • 5. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method IV. PERFORMANCE CHARACTERISTICS OF SESRIG 4.1. Results and discussion The variation of per unit frequency, magnetizing reactance, air gap voltage, stator phase voltage, stator phase current and output power with respect to change in per unit speed at different rotor resistance are given in tables 4.1,4.2, and 4.3. The stator voltage, stator current, frequency and output power characteristics of the SESRIG for different values of external rotor resistance RX2 shown in figures 4.1, 4.2 and 4.3 respectively. These figures show that, increase in speed has proportionate increase in output voltage, current, frequency and power. It is observed that increasing Rx2 has the effect of shifting the performance characteristics to the right-hand side of the speed axis. At a rotor speed of 1.05 p.u or above, the generator voltage or frequency can be maintained at rated value by varying RX2. This feature will be employed for voltage and frequency control of the SESRIG. It is observed that increasing Rx2 has the effect of shifting the performance characteristics to the right-hand side of the speed axis. At a rotor speed of 1.05 p.u or above, the generator voltage or frequency can be maintained at rated value by varying RX2. This feature will be employed for voltage and frequency control of the SESRIG. The operating speed range of the SESRIG depends upon the maximum value of R X2 available, the rated voltage of the rotor winding, as well as the mechanical constraints of the turbine The result shows that by varying rotor resistance values, the magnitude and frequency of voltage can be controlled over a wide speed range. The variation of per unit frequency, magnetizing reactance, air gap, stator phase voltage, and stator phase current, with respect to change in per unit speed at different stator resistance are given in tables 4.4, 4.5 and 4.6. The stator voltage, stator current, frequency characteristics of the SESRIG for different values of external stator resistance RX1 shown in figures 4.4, 4.5 and 4.6. respectively. The results from the figures show that, by varying stator resistance values, the magnitude of stator phase voltage and current can be controlled. But the frequency is remaining unchanged with respect to various stator resistances. The stator resistance has considerable influence over the stator voltage and current. So the characteristics are useful to design the machine for specified system. 4.2. Tabulation of Results 4.2.1 Effects of rotor resistance variations For, Rx2=0.00 p.u ; C=47μF ; RL=3 p.u b a Xm E1 V1 I1 Pout 0.9000 0.8663 1.8645 0.8375 0.7567 0.5348 0.5726 0.9500 0.9137 1.6671 0.9067 0.8702 0.6414 0.7572 1.0000 0.9610 1.4988 0.9627 0.9791 0.7515 0.9586 1.0500 1.0080 1.3542 1.0108 1.0870 0.8676 1.1816 1.1000 1.0550 1.2290 1.0524 1.1945 0.9901 1.4268 1.1500 1.1017 1.1200 1.0887 1.3018 1.1193 1.6946 1.2000 1.1482 1.0246 1.1204 1.4093 1.2553 1.9860 1.2500 1.1945 0.9406 1.1484 1.5172 1.3985 2.3019 1.3000 1.2406 0.8663 1.1731 1.6259 1.5491 2.6436 1.3500 1.2864 0.8004 1.1950 1.7356 1.7073 3.0122 1.4000 1.3320 0.7417 1.2145 1.8464 1.8734 3.4092 Table. 4.1. Results for various speed values at RX2=0.00 (all the values are in p.u) Rx2=0.00 p.u Rx2=0.18 p.u Rx2=0.36 p.u Rx2=0.54 p.u RL=3 p.u C=47μF Graph.4.1.Stator phase voltage with respect to per unit speed for various Rotor resistance values. 30
  • 6. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method For, Rx2=0.18p.u ; C=47μF ; RL=3 p.u B a Xm E1 V1 I1 Pout 0.90 0.8125 2.1321 0.6736 0.5664 0.3812 0.3208 0.95 0.8561 1.9113 0.8201 0.7312 0.5120 0.5346 1.00 0.8994 1.7229 0.8881 0.8372 0.6093 0.7008 1.05 0.9424 1.5610 0.9420 0.9367 0.7077 0.8774 1.10 0.9851 1.4208 0.9886 1.0349 0.8105 1.0710 1.15 1.0274 1.2986 1.0292 1.1321 0.9180 1.2816 1.20 1.0695 1.1916 1.0649 1.2285 1.0301 1.5093 1.25 1.1111 1.0973 1.0962 1.3244 1.1471 1.7542 1.30 1.1524 1.0139 1.1240 1.4201 1.2689 2.0166 1.35 1.1932 0.9397 1.1487 1.5155 1.3956 2.2968 1.40 1.2336 0.8735 1.1707 1.6110 1.5273 2.5953 Table 4.2. Results for various speed values at RX2=0.18 (all the values are in p.u) Rx2=0.00 p.u Rx2=0.18 p.u Rx2=0.36 p.u Rx2=0.54 p.u RL=3 p.u C=47μF Graph.4.2.Stator phase current with respect to per unit speed for various Rotor resistance values. For , Rx2=0.36 p.u ; C=47μF ; RL=3p.u b a Xm E1 V1 I1 Pout 0.90 0.7666 2.4069 0.0000 0.0000 0.0000 0.0000 0.95 0.8072 2.1616 0.6407 0.5349 0.3582 0.2861 1.00 0.8475 1.9523 0.8049 0.7095 0.4931 0.5035 1.05 0.8874 1.7723 0.8717 0.8092 0.5828 0.6549 1.10 0.9270 1.6165 0.9235 0.9011 0.6718 0.8119 1.15 0.9661 1.4807 0.9687 0.9914 0.7642 0.9828 1.20 1.0049 1.3617 1.0083 1.0804 0.8601 1.1673 1.25 1.0433 1.2568 1.0431 1.1684 0.9596 1.3652 1.30 1.0812 1.1640 1.0740 1.2555 1.0625 1.5763 1.35 1.1187 1.0815 1.1015 1.3419 1.1690 1.8008 1.40 1.1558 1.0078 1.1260 1.4278 1.2791 2.0386 Table 4.3. Results for various speed values at RX2=0.36 (all the values are in p.u) 31
  • 7. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method Rx2=0.00 p.u Rx2=0.18 p.u Rx2=0.36 p.u Rx2=0.54 p.u RL=3 p.u C=47μF Graph. 4.3. Per unit frequency with respect to per unit speed for various Rotor resistance values. For, Rx2=0.54p.u ; C=47μF ; RL=3 p.u B a Xm E1 V1 I1 Pout 1.00 0.8049 2.1743 0.6266 0.5215 0.3484 0.2720 1.05 0.8425 1.9763 0.7960 0.6971 0.4822 0.4859 1.10 0.8798 1.8048 0.8596 0.7903 0.5653 0.6246 1.15 0.9166 1.6554 0.9105 0.8771 0.6480 0.7692 1.20 0.9530 1.5245 0.9541 0.9611 0.7327 0.9237 1.25 0.9890 1.4090 0.9925 1.0438 0.8201 1.0895 1.30 1.0245 1.3068 1.0265 1.1253 0.9103 1.2662 1.35 1.0596 1.2159 1.0568 1.2057 1.0032 1.4538 1.40 1.0942 1.1348 1.0838 1.2853 1.0988 1.6520 Table 4.4. Results for various speed values at RX2=0.54 (all the values are in p.u) Rx2=0.00 p.u Rx2=0.18 p.u Rx2=0.36 p.u Rx2=0.54 p.u RL=3 p.u C=47μF Graph. 4.4. Per unit Output power with respect to per unit speed for various Rotor resistance values. 32
  • 8. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method 4.2.2. Effects of stator resistance variations For , Rx1=0.00 p.u ; C=47μF ; RL=3 p.u b a Xm E1 V1 I1 0.9000 0.8663 1.8645 0.8375 0.7567 0.5348 0.9500 0.9137 1.6671 0.9067 0.8702 0.6414 1.0000 0.9610 1.4988 0.9627 0.9791 0.7515 1.0500 1.0080 1.3542 1.0108 1.0870 0.8676 1.1000 1.0550 1.2290 1.0524 1.1945 0.9901 1.1500 1.1017 1.1200 1.0887 1.3018 1.1193 1.2000 1.1482 1.0246 1.1204 1.4093 1.2553 1.2500 1.1945 0.9406 1.1484 1.5172 1.3985 1.3000 1.2406 0.8663 1.1731 1.6259 1.5491 1.3500 1.2864 0.8004 1.1950 1.7356 1.7073 1.4000 1.3320 0.7417 1.2145 1.8464 1.8734 Table 4.5. Results for various speed values at RX1=0.00 (all the values are in p.u) Rx1=0.00 p.u Rx1=0.18 p.u Rx1=0.36 p.u Rx1=0.54 p.u RL=3 p.u C=47μF Graph.4.5. Stator phase voltage with respect to per unit speed for various stator resistance values For, Rx1=0.18 p.u ; C=47μF ; RL=3 p.u b a Xm E1 V1 I1 0.9000 0.8635 2.0729 0.7394 0.6182 0.4358 0.9500 0.9102 1.8658 0.8370 0.7413 0.5447 1.0000 0.9568 1.6897 0.8991 0.8414 0.6435 1.0500 1.0029 1.5370 0.9499 0.9368 0.7446 1.1000 1.0489 1.4060 0.9935 1.0306 0.8502 1.1500 1.0947 1.2921 1.0314 1.1231 0.9605 1.2000 1.1401 1.1926 1.0645 1.2147 1.0755 1.2500 1.1853 1.1053 1.0936 1.3055 1.1952 1.3000 1.2301 1.0283 1.1192 1.3956 1.3198 1.3500 1.2746 0.9603 1.1418 1.4853 1.4492 1.4000 1.3188 0.9000 1.1619 1.5745 1.5834 Table. 4.6. Results for various speed values at RX1=0.18 (all the values are in p.u) 33
  • 9. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method Rx1=0.00 p.u Rx1=0.18 p.u Rx1=0.36 p.u Rx1=0.54 p.u RL=3 p.u C=47μF Graph. 4.6. Stator phase current with respect to per unit speed for various stator resistance values. For, Rx1=0.36 p.u ; C=47μF ; RL=3 p.u B A Xm E1 V1 I1 0.9000 0.8619 2.3320 0.0000 0.0000 0.0000 0.9500 0.9084 2.1153 0.6923 0.5646 0.4142 1.0000 0.9546 1.9316 0.8126 0.6979 0.5328 1.0500 1.0003 1.7736 0.8712 0.7860 0.6234 1.1000 1.0460 1.6379 0.9164 0.8665 0.7131 1.1500 1.0913 1.5204 0.9555 0.9449 0.8059 1.2000 1.1364 1.4183 0.9894 1.0214 0.9017 1.2500 1.1811 1.3292 1.0191 1.0961 1.0005 1.3000 1.2256 1.2512 1.0450 1.1692 1.1022 1.3500 1.2698 1.1829 1.0677 1.2408 1.2066 Table 4.7. Results for various speed values at RX1=0.36 (all the values are in p.u) Rx1=0.00 p.u Rx1=0.18 p.u Rx1=0.36 p.u Rx1=0.54 p.u RL=3 p.u C=47μF Graph.4.7. Per unit frequency with respect to per unit speed for various stator resistance values. V. CONCLUSION In this paper of work the voltage and frequency control of a self excited slip ring induction generator by varying the external rotor resistance have been presented. Steady state modeling, performance and the control characteristic of the SESRIG have been developed from an equivalent circuit analysis. It is shown that with constant load and excitation capacitance, both frequency and the output voltage of the SESRIG can be maintained constant by varying rotor resistance over wide range of speeds without exceeding the specified stator current limit. In future it is planned to develop a suitable technique to vary the external rotor resistance automatically to achieve voltage and frequency control. BIBLIOGRAPHY [1]. Swati Devabhaktuni and S.V.Jayaram Kumar, “Selection of Capacitors for the Self Excited Slip ring Induction Generator with External Rotor Capacitance”, Journal of Energy Technologies and Policy, ISSN 2224-3232, Vol.2, No.2, 2012. [2]. T.F.Chan, K.A.Nigim, L.L.Lai, “ Voltage and frequency control of self excited slip ring induction generators”IEEE Trans, Energy Conversion vol 19, pp. 81-87, March 2004. [3]. T.F.Chan “Analysis of self-excited induction generators using an iterative method” IEEE Trans. Energy Conversion, vol 10, pp. 502-507, Sept .1995. [4]. E.G.Marra and J. A. Pomilio, “Induction – generator –based system providing regulated voltage with constant frequency”, IEEE Trans.Ind.Electron., vol.47,pp.908-914.Aug.2000. [5]. E.suarez and G. Bortolotto, “ Voltage- Frequency control of a self –excited Induction generator”,IEEE Trans. Energy conversion.vol.14,pp .394-401.Sep . 1999. 34
  • 10. Modeling and Analysis of Self Excited Slip Ring Induction Generator Using Newton Raphson Method [6]. Mustafa Al-saffar and Eui-cheol , “Controlled shunt capacitor self excited induction generator”, in proc.33rd IEEE Ind.applicate.soc.Annu.Meeting, vol.2, pp.1486-1490. 1998. [7]. K.A.Nigim, “ Static exciter for wound rotor induction machine”, in Proc.conf.rec.16 th Ind.applicat.Soc.Annu.Meeting, vol.2, pp.934-937. 1990. [8]. F.Girand and Z.M.Sa;meh “ Wind –driven , Variable- speed variable –frequency, double –output induction generator” Elect March power sys vol 26, pp 287-297,1998. [9]. S.S. Murthy. O.P. Malik and A.L.Tandon, “Analysis of self-excited induction generation” Procc . Inst. Eng…pt C, vol 129, No 6, pp260-265. Nov 1982. [10]. L.Ouazance and G.McPJherson , Jr “Analysis of the isolated induction generator” IEEE Trans, Power App Sys, vol PAS-102 pp 2793-2798 Aug 1983. [11]. L.Shridhar, Bhim Singh and C.S. Jha,"Improvement in the Characteristics of Self Excited Induction Generator", Paper no. 92 WM 02 0-8 EC, Presented at IEEE PES Winter Meeting. New York, 1992. [12]. S.S. Murthy, O.P. Malik and A.K. Tandon, "Analysis of self-excited induction generators", heedings of ZEE, Vol. l29, Part C, No. 6, pp.260-265, November 1982. [13]. Bhim Singh, R.K. Mishra and M.K.Vasantha, "Voltage Regulator for .Isolated Self Excited Cage Generators", to appear in Journal of Electric Power System Research, vol 24, no.2, pp. 75-83, 1992. [14]. N.H. Malik and AA. Mazi, "Capacitance requirements for isolated self excited induction generators", ZEEE Trenscrcticmr on Energy caulversion, Vol. EC-2, No. 1, pp. 62-68, March 1987. [15]. Chan, T.F, Nigim, K.A., Lai, L.L. “Voltage and frequency control of self-excited slip-ring induction generators”, Energy Conversion, IEEE Transactions ,March 2004, Dept. of Electr. Eng., Hong Kong Polytech. Univ., China Vol.19 , Issue: 1, pp. 81 – 87. [16]. Swati Devabhaktuni, S.V.Jayaram kumar, “Performance Analysis of Wind Turbine Driven Self-Excited Induction Generator with External Rotor Capacitance”, International Journal of Advanced Engineering Sciences AND Technologies, Vol.10, Issue No. 1, pp. 001 – 006. [17]. S. Wekhande and V. Agarwal (1999), “A new variable speed constant voltage controller for self-excited induction generator with minimum control requirements,” Proceedings on Power Electronics and Drives Systems Conference vol. 1, pp. 98 – 103. [18]. Olorunfemi Ojo, "The transient and qualitative performance of a self-excited single-phase induction generator,"Paper no. 95WM- 075-EC, to appear in IEEE ?Irans. onEnergy con version, 1995. [19]. M. B. Brennen and A. Abbondati, "Static exciter induction generator," IEEE ?Irans. OD Industry Applications,Vol. IAS-13, No. 5, pp. 422-428, 1977. [20]. Yaser Anagreh (2001), “Steady state performance of series DC motor powered by wind driven self-excited induction generator,” Proceedings on Rev. Energ. Ren: power Engineering, pp.9-15. [21]. Rajambal and C.Chellamuthu (2002), “Modeling and simulation of grid connected wind electric generating system,” Proceedings on IEEE region conference TENCON. Pp 1847 – 1852. vol. 3. APPENDIX -I CONSTANTS: f0=(-b*XC*X2+XL*XC-b*XL*XC-b*R1*RL-b*X1*XC); f1=(-b*X2*XL*XC-b*X2*R1*RL-b*X2*X1*XC); f2=(RL*R2+XC*X2+R1*RL+X1*XC); f3=(X2*XL*XC+X2*R1*RL+X2*X1*XC+X1*RL*R2+XL*R1*R2); f4=(b*XL*X2+b*X1*XL); f5=(b*X1*XL*X2); f6=(-XL*X2-X1*XL); f7=(X1*XL*X2); f8=(-RL*R2*XC); g0=(-XC*R2-RL*XC-R1*XC); g1=(-R2*XL*XC-R1*RL*R2-R2*X1*XC-X2*RL*XC-X2*R1*XC); g2=(-b*X2*RL-b*X1*RL-b*XL*R1); g3=(-b*X2*X1*RL-b*X2*XL*R1); g4=(XL*R2+X2*RL+X1*RL+XL*R1); g5=(XL*X1*R2+X2*X1*RL+X2*XL*R1); g6=(b*RL*XC+b*R1*XC); g7=(b*X2*RL*XC+b*X2*R1*XC); APPENDIX –II INDUCTION MACHINE PARAMETERS: Number of phases =3 Number of poles =4 Frequency =50 Hz Voltage =380V Current =4.5A Power =1.8 KW Connection =star Type =slip-ring R1 =0.0597 p.u X1 =0.118 p.u R2 =0.0982 p.u X2 =0.118 p.u 35