1. A division of the Jones-Blair Corporation “GREEN”STRENGTH IN TODAY’S ROOFING

3. 45-year history as the innovators in Polymeric Coating Technology, and 75 years in the Coating Industry

4. An international network of Licensed Applicators plus Performance Based Contractors

6. UL Class “A” Fire Rated

7. Recognized by Factory Mutual

8. LEED Friendly

9. Miami Dade County Approved

10. Member of U.S. Green Building Council

11. CRRC

14. Cool Roofs absorb less than 35% of solar energy striking the roof

15. Compared to “traditional” dark roofs absorbing 70% or more of the solar energy

16. Results in reduced heat transfer into building, reducing cooling costsTraditional Dark Roof Absorbs 70% more Solar Energy Reflective White Cool Roofs C Can be %0* to 60*F Cooler

20. 65% Initial

21. 50% Aged (+3 years – actual)

22. NEOGARD® White Coatings:

23. Acrylic

24. Initial: 74% Aged: 68%

25. Silicone

26. Initial: 75% Aged: 75%

27. Polyurethane (7443)

28. Initial: 76% Aged 76%

29. Polyurethane (70613)

31. The higher the %, the better

32. LEED Green Building Rating System specifies Emittance at least 90%

33. NEOGARD® White Roof Coatings EXCEED LEED Emissivity Requirements.

34. LEED Combines ENERGY STAR® Reflectance Requirements with +90% Emittance

35. NEOGARD® White Coatings Emittance:

36. Acrylic – 94%

37. Silicone – 93%

38. Polyurethane (7443) – 95%

40. Nearly ½ of all Energy Consumption

41. 15 trillion gallons per year for all potable water

42. 136 million tons of building-related construction and demolition in a single year is generated

43. Buildings use 40% of all raw materials globally (3 billion tons annually)

44. $40 billion is spent annually to air condition buildings in the US

45. Electrical loads are increasing faster than Generating Capacity

46. Natural Gas & Electrical Costs are increasing

47. ½ of the US population live in Heat Islands

49. Cost of Roofing Materials

50. Premature Failures

51. Landfills Filling Up

52. Extending the life of an existing building by conserving natural resources, qualifies for credit in the Material and Resource category. By using the existing roof, reduction of waste is achieved and applies to further credits within this category.Before After

53. URBAN HEAT ISLANDS The use of dark, non-reflective surfaces for parking, roofs, walkways and other surfaces contributes to heat island effects created when heat from the sun is absorbed and radiated back to surrounding areas. As a result of heat island effects, ambient temperatures in urban areas can be artificially elevated by more than 10 degrees when compared with surrounding suburban and undeveloped areas. This results in increased cooling loads in the summer, requiring larger HVAC equipment and energy for building operations. Heat island effects can be mitigated through the application of shading and the use of materials that reflect the sun’s heat instead of absorbing it. Heat Island Atlanta 1972 Heat Island Atlanta 1993 Causes: Urban Trees/Grass/Shrubs Reduction (56% of the cause) Dark Roads & Parking Spaces (6%) Buildings with Dark Roof Surfaces (38%) Dark Surface Temps 75* - 100*F Higher than ambient air temperature Increases A/C costs (+$5 BILLION per year) Increases Smog Premature roofing material deterioration Roof Top Effects On Urban Heat Islands Roofs are the hottest urban features 140* to 180*F at peak Roofs cover 20% of land area Difficult to shade large low slope roofs Cool Roofing can make a big impact 100*F to 120*F at peak for cool Roofs 50* drop over 20% of an urban area Note: Computer Simulations project Significant Impact on UHI turning roofs Black to White

55. Reduce Energy Consumption by 15% or more?

56. Reduce Electrical Bills by 20% or more?

57. Reduce Roof Waste to Landfills by a 1/3 or more?

58. Protect Membrane, Bitumen, Metal & Concrete Roofs?

59. Improves bottom line by reducing waste and costs.

60. Resource and re-use of existing materials

61. Improves top line by providing new sources of revenues

62. Reduces the total cost of ownership for building owners by reducing life cycle costsElastomeric roof coating process: Vacuumed & Prepared Base Coat Top or Finish Coat

64. Single-Ply Membranes

65. Concrete Roof Decks

66. Metal Roofs

68. Primer: Required on some substrates

69. Coating: Apply a monolithic urethane coating across the entire roof using high quality compatible materialsBefore After

70. Environmental “Green” Advantages of Direct Bond Roofs Dade County approved; FM Global; UL rated; Energy Star rated; Cool Roof rated; Products LEED qualified Light reflective white coating (up to 94% solar reflectivity – SRI) One-part urethane membrane (toughest, most durable fluid-applied membrane on the market) Helps keep your building cooler (lower energy expense) Low odor Reduces hazardous waste disposal costs Less waste in landfills Renewable and sustainable roof system

71. TAX ADVANTAGES According to Sec. 1.162-4 Repairs of IRS Tax Code: Roof maintenance systems are fully tax deductable as an operating expense. One of the key advantages of a restoration system over a new roof system is in how it is classified by the IRS. Restoration is classified as a maintenance, and in most cases it can be expensed in the accounting period it is incurred. On the other hand a new roof system is a capital asset that must be amortized over a 39 year life.

72. ROOF PICTORIALS

73. A division of the Jones-Blair Corporation ELASTA-GARD DIRECT-BOND, FLUID-APPLIED ROOF SYSTEMS COMPATIBLE OVER: - BUILT-UP ROOFING (BUR) - MODIFIED BITUMEN (MB) - SINGLE-PLY - EPDM - METAL - CONCRETE

74. Urethane vsAcrylic Acrylics Tensile Strength – 300 psi Elongation – 300% Water Absorption – 20% Low Impact Resistance Suspect to Chemical Attack Urethane Tensile Strength – 1,500 psi Elongation – 360% Water Absorption - <3% High Impact Resistance Chemical Resistant Urethane is used exclusively for all Elasta-Gard Direct Bond Systems

75. ELASTA-GARD BUR/MB NEOGARD®’s Premier Roof Coating Membrane System Advantages: - Eliminates back-breaking tear-off of existing roof - Eliminates landfill costs. No disposal of old roofs - Sustainable and renewable, not replaced - NO SEAMS TO FAIL!! - All NEOGARD® products are Cool Roof, LEED qualified

76. Existing Mod-Bit Roof Failed Seams! “Fishmouth” Tear-off isn’t the only solution!!

77. Granules 60 mils fluid-applied urethane membrane

78. NO SEAMS!!! Elasta-Gard BUR/MB (Heavy Traffic Fluid-Applied Roof System with Granules) ALL SEAMS ARE DETAILED AND TAPED IF NECESSARY Primer – 7780/7781; 1/3 gal/100 sq.ft. Base Coat – 39 dry mils of high quality urethane Topcoat – 21 dry mils of WHITE (COOL ROOF, LEED qualified) high quality urethane Granules broadcast to refusal on topcoat Total System Membrane Thickness Averages 60 dry mils

79. ELASTA-GARD LT Over modified bitumen Leak Problem Areas

80. Seams detailed Drains detailed Protrusions detailed

81. Urethane Base Coat 7419 HB 2 gallons/100 sq.ft. 26 dry mils Tensile Strength – 350 psi Elongation – 500%

82. Topcoat being applied Topcoat can either be sprayed or rolled. Rolled during windy conditions Notice how parapet walls are sealed

83. NO SEAMS!!! Urethane Topcoat 70613 – white 1 gallon/100 sq.ft. 12 dry mils Tensile Strength – 1,500 psi Elongation – 360% Total system coating thickness averages 38 dry mils

84. ELASTA-GARD SPSingle-Ply Rubber Roof

85. Encapsulate parapet wall with polyurethane foam Seam Tape

86. SEAM DETAIL

87. Topcoat Base Coat

88. Urethane Topcoat 70613 – white 1 gallon/100 sq.ft. 12 dry mils Tensile Strength – 1,500 psi Elongation – 360% Total system coating thickness averages 38 dry mils

89. Elasta-Gard C (concrete) LEED qualified white topcoat High-build base coat

90. ELASTA-GARD M NEOGARD® Metal Roof Coating Membrane System York Label Company Kansas City, MO Curt Carpenter Owner - C&G COATINGS Your NEOGARD®Representative

91. 60,000 sq.ft. metal roof Roof before applying coating membrane

92. Roof before applying coating membrane

93. Assets to protect...... Leaks

94. Prep Work

95. Seal Penetrations & Vertical Seams with Polyurethane Foam Polyurethane foam Polyurethane foam on vertical seams

96. Caulk & Apply Basecoat to Screws Tape & coating on holes Caulk & Coating

97. Horizontal Seams Taped & Base Coated

98. All Seams & Screws Base Coated Prior to Applying the Topcoat Roof is totally waterproofed prior to application of white topcoat

99. Finish Pics!

102. Before After

103. Acrylithane MRC Topcoat over Metal (any color can be matched) After Before

104. Ritz-Carlton Hotel – Biloxi, MS

105. LEED Qualified, Cool Roof Rated Topcoat Test Patch Free application to qualified facility Base Coat Primer

106. A division of the Jones-Blair Corporation Polyurethane Foam Roof Systems COMPATIBLE OVER: - BUILT-UP ROOFING (BUR) - MODIFIED BITUMEN (MB) - SINGLE-PLY - EPDM - METAL - CONCRETE

108. Lightweight (50# per 100 square feet)

109. Self-Flashing

110. Insulation Value (7.14 R-value per inch)

113. 2 Base Coats – 37 Mils

114. 2 Topcoats – 18 MilsTotal 55 Mils Coating w/granules Polyurethane Foamover metal roof 15-year Hail Resistant Warranty

115. Rubber Roof with River Rock

116. Rubber Secured with I-90 Wind Uplift Rated Fasteners

117. Foam Applied Over Rubber Self-flashing

118. Base Coat Applied

119. Permathane II FR Polyurethane Foam Roof Everything is SEALED Cool Roof, LEED Qualified Topcoat

120. An Option To Tearing Off A Polyurethane Roof That Has Not Been Maintained………………..

121. Independence Middle School, OKC Foam Roof not maintained since 1984

122. Scarifying the coating and ¼” of the foam base

123. Hard to reach areas will be hand grinded

124. Before 10-year Permathane II FR Warranty CURT CARPENTER -- C&G COATINGS

125. If it’s good enough for the New Orleans Superdome……………….. Polyurethane Foam Base with NEOGARD®Urethane Coating Re-roofed after Hurricane Katrina damage in 2006

126. CURTCARPENTER C&G COATINGS Your NEOGARD® Representative Thank you for your time. Please feel free to contact me for an estimate or more information on the NEOGARD®product and application that’s right for you. 8228 Marshall Dr. Lenexa, KS 66214 913-438-2412 – office 913-634-2588 – cell 913-492-4362 – fax cgcoatings@kcnet.com www.cgcoatings.com www.neogard.com