No-1 Call Girls In Goa 93193 VIP 73153 Escort service In North Goa Panaji, Ca...
Â
Sme 248-reiff-injection-molding-tour-lowres
1. PLANT TOUR SYNOPSIS: R E I F F I N J E C T I O N M O L D I N G, S P O K A N E W A . 1 7 J A N U A R Y 2 0 0 7
Society of Manufacturing Engineers
Inland Northwest Chapter 248 • Spokane, Washington
INDEX TERMS:
Thermoplastics
http://en.wikipedia.org/wiki/
Thermoplastic
Injection Molding
http://en.wikipedia.org/wiki/
injection_molding
Hot Stamping
Ultrasonic Welding
http://en.wikipedia.org/wiki/
Ultrasonic_welding Figure 1 —SME Chapter 248 member and Reiff Injection Molding owner Jim McCall explains
operation of the company’s Cincinnati-Milacron 300 ton x 30 oz. shot plastic injection molder.
P L A N T T O U R S Y N O P S I S:
REIFF INJECTION Reiff Injection Molding — Success from Adaptation...
M OLDING , S P O K A N E Case History/Plant Tour – Spokane, Washington., Jan. 23, 2007 by Dave Davidson. Photos by Ray McDied
W A. 1 7 J ANUARY 2 0 0 7 Jim and J. McCall own and operate Reiff Injection Molding Co., a manufacturer of plas-
tic injection molded parts originally established in 1979 in Walla Walla, WA. The com-
Inland NW Chapter 248 Contacts: pany moved to Spokane, WA in 1999 and recently moved from its University Road op-
eration to larger facilities located at 131 N. Pittsburg close to the Altamont exit on I-90.
Vice Chair: Tony Wisniewski The company runs four different plastic
Chair-Elect: Douglas McGuire injection molding machines, and manu-
Treasurer: Robert Ladd factures parts for a variety of industries
including the medical, telecom, irriga-
Secretary: Dean Croskey
tion and recreation industries.
Newsletter: Dan Tabish
Challenges: Like many American
Webmaster: Matt Feider manufacturers, Reiff has faced serious
http://chapters/sme.org/248 challenges due to the outsourcing of
products overseas. The company faced
2007 Chair: David A. Davidson a severe test when one of its major cus-
Deburring/Surface Finish tomers, a subsidiary of a Fortune 500
firm decided it was going to start out-
Specialist sourcing product from India. This Reiff Molding has developed unusually close
VoiceMail: (509)-230-6821 change was particularly unsettling as it relationships with customers and provides in-
(e): ddavidson@mgnh.dyndns.org would mean not only loss of one of the house custom engineering and specially tai-
company's largest customers, but the lored production and inventory programs that
www.deburringsolutions.com facility in which the company operated. anticipates customer needs and requirements.
2. Plant tour synopsis: Reiff Injection Molding, SME Chapter 248
Spokane Wa. 17 January 2007
D. A. Davidson [ed.]
Plant Tours — Collaborative opportunities for cross-pollination of ideas
for manufacturing, services and lean process implementation...
PAGE 2
(Cont’d from p. 1) but the loss of the company facilities
as well, as the large customer had been providing facili-
ties for the plastic injection molding operation for its
own convenience.
The company has not only survived but has success-
fully expanded its business through utilizing its internal
strengths to provide exceptional customer service that
competitors find difficult to duplicate. As a family busi-
ness, father Jim McCall has a strong process and op-
erations background working with Whirlpool Corpora-
tion in Michigan after receiving a master’s degree in
engineering from the University of Michigan. Son, J.
McCall, has a strong plastic materials background with
a degree from Western Washington University. To-
gether, they are in a position to not only offer manufac-
turing services but custom engineering development
and materials selection advice to customers who need
this kind of process development assistance to take
parts from prints in the design stage and turn them into
reality. They have locked in customer relationships not
Figure 3 — SME Chapter 248 members listen as owners Jim and Jay only by being a manufacturing source for plastic molded
McCall explain their operation as well as the basic principles involved products, but by also being a design and engineering
in transforming thermoplastic granular feedstock used as the basic raw resource to customers who have new product in the
material into molded products by carefully controlled heat and pressure formative stage. They are especially adept at assisting
customers in modifying or tweaking original designs in
such a way to make actual production operations more
practical, feasible and cost efficient.
As an example of this, Jim McCall, explained an espe-
cially challenging design and operational problem the
company had been faced with recently involving “puffer
nozzles”. This molded component is part of a sophisti-
cated quality assurance system used in the food and
produce industry. As items are passed down the length
of an inspection conveyor they are analyzed by an opti-
cal/video system which can identify defective or non-
conforming items. Once an identification has been
made the system will remove the offending item from
the production stream by actuating the “puffer nozzle”
which then directs a “puff” or “blast” of high velocity air
at the defective piece as it comes off the conveyor, seg-
regating it from acceptable product. The “puffer noz-
zle” is a challenging product for the plastic injection
molding process where products are typically designed
with a specific taper to promote ease of ejection from
the mold at the end of the injection cycle. On this part
Figure 4 — Plastic Injection Molding cell at Reiff Injection Molding the internal orifice had to be designed with a taper op-
Inc., plant tour attendees watch as Jim and J. McCall explain opera- posite to that which would be normal for ejection pur-
tions of the four machines in the cell including: (1) BOY 25 Ton x 1 oz. poses in order to produce sufficient velocity in the air
(2) Toshiba 85 &on x 3.2 oz. (3) Toshiba 190 Ton x 10 oz. (4) Cincin- puff used to remove the piece from the conveyor
nati-Milacron 300 Ton x 30 oz stream.
3. Plant tour synopsis: Reiff Injection Molding, SME Chapter 248
Spokane Wa. 17 January 2007
D. A. DAVIDSON (ED.)
Reiff Injection Molding —Success from extensive process
technology knowledge coupled with customer need anticipation
PAGE 3
Customer Service: The other weapon in Reiff’s
arsenal is customer service that goes the extra
mile after the parts have moved from the design
stage and into production stage. Marilyn McCall
manages office operations and closely monitors
customer needs. The company has developed
such close relationships with customers that it
provides what the Wall Street Journal has re-
cently described as the next level of customer
service — not just meeting customer needs and
desires, but in some cases — anticipating them.
The company has also carved out a special
niche strategy in that it avoids becoming a com-
modity supplier, but focuses its attention on cus-
tomers who need the kind of quick response for
shorter runs of parts that have become Reiff’s
specialty. The company has also recently ac-
quired marketing rights to one of its major prod-
uct lines “The Gripper Caddy” (shown in the pic-
Figure 5 — J. McCall explains operation of the computer controls on the com- ture on page 1)
pany’s TOSHIBA 190 Ton x 10 oz. injection molding machine to Jeff Dorner- The Reiff success story then is a combination
berg, an associate professor in the Mechanical Engineering Dept. at Eastern of highly effective customer assistance at the
Washington University. The university located in Cheney, WA. was a recipient design and engineering level coupled with out-
of an SME Education Foundation grant ($220,000.00) used in the construction standing responsiveness to customer needs once
of it’s new computer science facility. part production has begun. ?
Plant Tours: cross-pollination opportunities:
SME and SME chapters have a strong tradition of
arranging plant tours for members to view opera-
tions in a wide cross section of industry and busi-
ness. Recently this concept was taken to the
next level when SME arranged for COLLABORATE
2006 an event designed to draw attendees from
across industry to share ideas on everything from
new manufacturing techniques to lean implemen-
tation. Participants included representatives
from Toyota, Daimler, Lockheed, Northrop, Ford,
the Army and others. In addition to attending
technical and networking sessions, pLant tours of
Siemens Electronics and Boeing Delta Rocket
Figure 6 — The plastic injection molding cell at Reiff Molding includes four assembly facilities were offered.
different injection molding machines of varying capacities. The smallest ma- NEXT TOUR: 6:00 PM February 23, 2007
chine is a 25 ton x 1 oz, where as the largest is rated for 300 ton x 30 oz. The “Lean” Plant Tour, MacKay Manufacturing, Spo-
first figure is a reference to the amount of force the screw mechanism is capa- kane WA.. With the Inland Northwest Lean Man-
ble of exerting when pressing the mold segments together. The second figure agement Consortium. Details to follow
refers to the maximum amount of raw plastic material that can be injected.