The document lists and provides specifications for various furniture parts and accessories, including: heavy duty swivel chair bases, rocker bases, steam bent and cut oak rocker runners, curved rocking chair seats, oak hip huggers, hip hugger clips, Morris chair brackets and rods, platform rocker springs, oak high chair parts, bent oak high chair tray arms, high chair tray hardware, high chair safety straps, and finials, spindles and pegs of various sizes. Dimensions and materials are provided for each part.

1. Furniture Fittings and Accessories Components
Chair Parts
Heavy Duty Swivel
12 gauge steel with a double race 10 1/4 by 10 1/4 flat pitch.
Mounting holes are on 8" centers
Swivel Rocker base
Brown legs with plastic feet. Leg span is 25" and comes in
either a 5 1/4" or 6" overall height.
Steam Bent Oak Rocker Runners
Length measures strait across from tip to tip. Stronger than
cut rockers Sold in pairs only. Unfinished red oak will require
drilling sanding and finishing.
1 5/16" high by 34 1/4" long by 5/8" thick
1 5/16" high by 34 1/4" long by 1 1/8" thick
1 5/16" high by 34 1/4" long by 1 7/8" thick
Cut Oak Rocker Runners
1 3/4" high by 34 1/2" long by 1 1/16" thick
1 3/4" high by 37" long by 1 9/16" thick
Curved Rocking Chair Seat
Oak face and back. It must be shaped and cut to fit your
particular rocker. Send us a sketch of your formed shape
before ordering to make sure it will fit. We can provide this
one curvature only. Our supplier doesn't have any other
zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 1

2. Furniture Fittings and Accessories Components
shape molds. 24" to 25"long following the curve. 3/16" thick,
20" plus wide.
Oak Hip Huggers
6 1/2" high by 5 1/4" deep by 7/8" diameter. 11" long from tip
to tip measuring along the curve. **Please note: All
measurements are approximate. One end is sanded flat to fit
the chair seat. The other end is carved out to fit the back
spindle. Screw holes are pre-drilled. Unfinished, sanded,
ready to install. Ends are pointed. One left hand and one right
hand hip hugger required per chair. Sold in pairs only.
Hip hugger Clips
Outside dimensions - 1" long by 11/16" wide by 1/2" high.
Screw hole - 1/4" diameter. Made to fit 7/8" hiphuggers. Sold
in sets of four.
Morris Chair Brackets
7 3/4" long by 15/16" wide. Hooks will accommodate 3/8" to
1/2" diameter rods. The common angle of the brackets will
adapt to the curve of most Morris chairs. Sold by the pair.
Morris Chair Rod
Overall - 29 3/4" long.
Rod - 28 1/4" long by 3/8" diameter. Beehive finials - 3/4"
long by 7/8" diameter.
Finials are attached with set screws which can be removed,
allowing the rod to be cut to length if necessary.
zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 2

3. Furniture Fittings and Accessories Components
Platform Rocker Springs
All springs are sold by the pair which will do one chair.
Heavy Duty - 7 gauge Eight turns.
Single Juvenile Platform Rocker Springs.
Oak High Chair Parts
20 1/2" wide 11 3/4" deep. 1 3/32" thick with Routed
center.
16" wide by 8 1/2" deep at center. 7" deep at ends.
16" wide by 8" deep.
Bent Oak High Chair Tray Arms
Overall length - 18 1/2" long 23" long following the curve.
Flat area - Approximately 13" 7/8" Square. Sold by the pair
with spacers.
High Chair Tray Hardware
Arm piece - 6" L x 5/8" w x 7/8" deep. Tray Piece - 3 5/16" L
x 1" w x 15/16" deep.
Best for use with our W3-5226 tray or similar styles only.
Comes as a set for attaching one high chair tray. The long
piece attaches to the outside of the arm. The short piece
attaches to the underside of the tray. The spring loaded clamp
allow the position of the tray to be adjusted then locked into
zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 3

4. Furniture Fittings and Accessories Components
place.
High Chair Safety Strap
13" long by 5/8" wide Natural leather. Includes screw snap
for easy installation.
Finials, Spindles, Pegs
5 inches tall and 3 inches in diameter Pine
Pine fence post finial 4 1/2" tall and 3"
Turned length - 2 1/4" Overall length - 3 1/8"
Maximum diameter - 15/16" Tenon diameter - 3/8"
zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 4

5. Furniture Fittings and Accessories Components
Turned length - 3 3/32" Overall length - 3 3/4"
maximum diameter - 1 5/8" Tenon diameter - 3/8"
Turned length - 2" Overall length - 2 7/16"
Maximum diameter - 13/16" Tenon diameter - 1/2"
zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 5

6. Furniture Fittings and Accessories Components
Turned length - 3 3/32" Overall length - 3 3/4"
maximum diameter - 1 5/8" Tenon diameter - 3/8"
Turned length - 2" Overall length - 2 7/16"
Maximum diameter - 13/16" Tenon diameter - 1/2"
zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 5